Products

12" Dual Wheel Upgrade Kit for Seamax EZ Load, and 2017 Deluxe Launching Wheel or Earlier

79.00 USD

Provide a 4-Wheels system option to "Deluxe Launching Wheels 2017 or Earlier Model" and "Easy Load Launching Wheels". (12" Wheel Version)

Suggested for larger boat with wider transom. Provide better support on soft terrain and sandy beach.

Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

Package includes: 2 x 12 inches Pneumatic tire, 2 x dual wheel bearing.

Axle Hole diameter: 1 inch

Note: this upgrade kit requires an existing full set of Seamax "Deluxe Launching Wheels" or "Easy Load Launching Wheels".

12V Alligator Clip to Cigarette Lighter Plug Converter for SUP20 Air Pump

15.00 USD

Connect 12V Cigarette Lighter Plug directly to 12V battery terminals

Suitable for Seamax SUP20S & SUP20D 12V electric air pump

Wire length: 16", Gauge for: 15A

Suggested 12V battery capacity: minimum 7AH when using with SUP20 Pump

14" Dual Wheel Upgrade Kit for Seamax Deluxe Boat Launching Wheels 2019 Version

99.00 USD

Provide a 4-Wheels system option to "Deluxe Launching Wheels"  (14" Wheel Version * 2019)

Suggested for larger boat with wider transom. Provide better support on soft terrain and sandy beach.

Our new tires are now 14” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

Package includes: 2 x 14 inches Pneumatic tire, 2 x dual wheel bearing. Marine grade tire and inner tube. overall width of tire 3-3/4 inches

Axle Hole diameter: 1 inch

Note: this upgrade kit requires an existing full set of Seamax Deluxe Launching Wheels with 14 inches Wheels  (Some of photo showing the 12" wheel but we will ship 14" kit)

2 x 12" Marine Grade Pneumatic Wheels for Seamax Boat Launching Dolly (one pair)

59.00 USD

Suitable for 12" Wheel Version Seamax Boat Launching Wheels Set (All models with 1" diameter axle)

Wheel Model: 4.10/3.50-6

Max Tire Diameter: 12 inches

Wheel Axle Diameter: 1 inch

Suggested Air Pressure:  12 to 15 PSI  (Max 30PSI)

Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

Note: Not intended for highway use. Rinse the product with fresh water after use in salt water. Cover from sun light when no in use and maximize the life time.

7L Single Stage Foot Pump for Inflatable Boats, Max 3.6 PSI Support Inflation and Deflation

39.00 USD

Reliable foot pump for your inflatable boats and water toys.

Excellent inflator/ deflator manual foot pumps are great for all inflatable boats, rafts, kayaks, water toys and more.

Reinforced fabric coated bellows. All stainless steel parts.

Includes Halkey-Roberts twist-lock valve and inflation nozzles, 4-1/2' inflation hose and universal adapters.

Also come with dual O-ring for different version of air valve.

Easy to collapse and store, compact and portable to be carried around

1 year warranty parts and labor.

9L Foot Pump with Double Chambers, High Volume and High Pressure, Max 15 PSI for Inflatable Boat and SUP

55.00 USD

Double chamber system. High-volume-low-pressure mode (4.4 psi). Or low-volume high-pressure mode (14.5 psi).

Universal Halkey-Roberts (HR) valve adapter for popular HR, Bravo, and Naru air valves.

2 x grooved rubber O-ring. Thickness: 4 mm and 5 mm.

Durable Nylon reinforced fiberglass. Crush resistant universal air hose.

Dimension: 13” x 9” x 2-1/2”.

Air hose length: 55”

Aluminium Portable Boat Carry and Launching Hand Dolly Set

449.00 USD

Features

Aluminum Oars Set

40.00 USD

2 x Aluminum Oars with Quick Lock Pin

Available assembled lengths: 5.3, 5.7, 6 Feet

Black or Grey color to choose from 

Suitable Oar Length:
5.3 FT oars for up to 10.5 FT boats
5.7 FT oars for 12.5 FT to 15.5 FT boats
6 FT oars for 16.5 FT to 20 FT boats

Aurora Speed Cleaner and UV Protector Maintenance Kit for Hypalon and PVC Inflatable Boats

75.00 USD

• Speed Cleaner/ Restorer (450 ml.) quickly and easily removes stubborn Dirt, Grime, Stains, Oxidation, and stuffs from all inflatable boat surfaces.
• Poly Guard (220 ml.) protects the inflatable boat against UV damage, Dirt, Grime, Diesel, Soot, Stains, Bird Droppings and more. Beautiful shine and not greasy or slippery.

Bench Seat Cushion with Detachable Under Seat Storage Bag for All Inflatable Boats

Sold Out

• Water-resistant material: 600D Polyester coated PVC, Dark Gray
• Multiple sizes for various bench seat lengths
• Multiple pockets for storage
• Extra easy-to-access side pockets for often-used small items, such as bottled drinks, and fishing gears
• 3-adjustable quick locks with tie-down straps for fast and easy attaching the cushion to the bench seat
• 3 bottom drain holes in the main compartment
• Help to keep personal belonging and gear dry and safe on the boat

Choosing a Right Size

Seamax seat cushions are suitable for most standard plywood or aluminum bench seat. The seat cushion covers the max 9-inches width bench seat, and the standard is 8 inches width. The seat cushion length could be up to 2-inches shorter than the bench seat for best result, which gives approximate 1-inch gap on each side of the seat. 

Bench Seat, Marine Grade Aluminum, with Seat Brackets

55.00 USD

• Marine Grade Aluminum
• Heave duty plastic seat brackets
• Width: 8" (approx.)
• Length: various
• Package contents: 1x aluminum bench seat, 2x seat bracket 

Additional Information (Standard 2012)

Seamax AIR270, AIR320, Ocean320, HD330 - Size A 34"
Seamax Ocean380, Sport 360, HD360, HD380, Ocean380T (Ver. 2012) - Size B 37"
Seamax Ocean430, Sport430, HD430, HD470, Ocean430T (Ver. 2012) - Size C 42"
Seamax Ocean 500T (2012 Version or Earlier) - Size D 49"

NEW Ocean T Series since 2014 Version ( PVC or Hypalon)

Ocean380T (2018) - Length 40"
Ocean430T - 470T (2018)  -  Length 45"
Ocean500T - 600T (2018) - Length 52"

Bimini: Aluminium Oar Lock Spacer

25.00 USD

2 Pairs of Aluminum Bimini Top Oar Lock Spacers

• Outer Ring Diameter: 3/4"
• Inner Ring Diameter: 3/8"
• Height: 3/4"

Bimini: Eye End Inner Cap for 1" Pole, 360 Degree Turning Hole, Stainless Steel

55.00 USD

Package contents: 2x stainless steel  inner cap with 360 degree turning hole, 4x rivet

Cap diameter: 0.81" (for 1" diameter bimini pole)
Hole diameter: 0.4"

Note: installation requires drilling the existing pole and using rivet gun

Bimini: Eye End Outer Cap for 1" Pole, Marine Grade Nylon

25.00 USD

Package contents: 2x marine grade nylon eye-end cap, 4x rivet

Hole diameter: 1/4"
Cap diameter: 1"
Height: 2-1/2"

Note: installation requires drilling the existing pole and using rivet gun

Black Fiberglass Reinforced Nylon Propeller Kit for Seamax PowerMax Models Trolling Motor

35.00 USD

Newly re-designed Black fiberglass reinforced composite material propeller, updated pitch, camber and thickness for high thrust application. Better performance with new propeller and minimizes efficiency lost through cavitation. 

Suitable for Seamax 2019 PowerMax edition trolling motor. Fiberglass Reinforced Black Nylon 3 Blade Propeller. Package included: Stainless steel washer, screw cap, and lock pin; (British system & metric system tighten hardware are both included)

Replacing the Propeller (Refer to User Manual, Page 8).

To replace the propeller, hold the blade and loosen the nut using the propeller wrench (Fig. D). Remove the nut and propeller. If propeller is stuck, hold one blade by hand and tap on the back side of the other blade with a hard blunt object. If necessary, repeat the procedure for the other blade until the propeller comes off. If propeller pin is bent, replace it. Align pin (Fig. E) when refitting propeller and tighten nut securely.

Blue Portable Electric Air Pump 1 - 8.5 PSI for Inflatable Boats and Inflatable Kites (with Built-in 7AH Rechargeable Battery)

215.00 USD

• Specifications
• Features
• Warranty

• Specifications

  Turbo Fan Stage: Max Pump Air 500L per Minute
  Dual Cylinder Stage: Max Working Pressure 60 Kpa (8.5 PSI)
  Digital Air Gauge. Built-in 12V/7AH battery with 110V-240V Smart Charger.
  Air Host Kit.
  Max 45 Minutes Working Time per Battery Charging
  Pressure Setting from 1PSI, Increment per 1 KPA (0.15PSI)
  Multiple Valve Adapters, Digital Control and Real Time Monitoring, Auto Shuts Off when Set Pressure Achieved
  LCD Back Light, Carrying Bag, Support Intake & Outtake (Inflate & Deflate) Dual Actions. 
  
  

  Additional Information

  This pump is suitable for the products that are using the Boston type, HR (Halkey-Roberts), Bravo or similar type air valve, Leafield valve etc. This kind of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. We have the Pump in Kite version, Please know the Kite version pump also good for Inflatable boats and all application same as the regular pump version.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.
  
  Use for Deflation - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.

• Features

  Supported Air Valves - This pump is suitable for the products that are using the HR (Halkey-Roberts), Bravo or similar type air valve. This kind of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. This Pump is the Kite version, Please know the Kite version pump is also good for Inflatable boats and all application same as the regular pump version.
  
  About this pump - Turn on the POWER switch and enter the maximum desired pressure by using the Set Pressure buttons, the set pressure will be shown on the right hand side of LCD screen. (10KPa = 100mbr = 1.45 PSI). Factory default working pressure is set as 25KPa (3.6 PSI).This pressure is suitable for most inflatable boats.
  
  Use as a Deflator - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.
  
  Built-in Battery - 80DB model has a built-in battery and travel charger. The type of this battery is 12V gel battery, lead acid type, battery capacity 7AH to support max 45 minutes working time. The battery will have up to 500 Cycles and 8 years life time if you can follow this maintenance manual. The charger is 110/240V travel type with double charging procedures. When you plug in the charge and connect with the pump, a red light showing on the charger can indicate the battery charging. The max charging current is 1A from the charger.
  
  Using the Pump Min set pressure is 1 PSI (8Kpa), if you only need lower pressure than 1 PSI, you can keep monitoring the screen pressure reading and stop the pump manually. Press the POWER button to start. During inflation, the left hand side of LCD screen should show the pressure that the pump has reached. As soon as the entered pressure has been reached, the inflator turns off automatically. And the inflator can be turned off at any time by pressing the POWER button again. Take off the air hose from the chamber once the pump stops pumping. It is possible to stop the inflator at any time by pressing the (OFF) switch.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.

• Warranty

  For recreational use, the electrical control boards, motor, charger are guaranteed for 2 years. Battery, air hose, valve adapters and carrying bag are guaranteed for 6 months. Warranty for commercial use is limited to six months from purchase date, and 90 days warranty for battery.

Blue Portable Electric Air Pump 1 - 8.5 PSI for Inflatable Boats and Inflatable Kites (without Battery)

Sold Out

• Specifications
• Pump Operation
• Warranty

• Specifications

  Interface: LCD display with back light
  Powertrain: Dual Motors and Double Stages, Electric Control, High Pressure Compressor
  Standard Voltage Input: DC12V / Current: 10A to 40A MAX / Max Power Dissipation: 500W
  Max. Inlet Air: 500L per Min / Max Working Pressure: 60Kpa (8.5 PSI)
  Pressure Increments: Per 1Kpa / 0.15 PSI / Build in Digital Air Gauge
  Maximum Continuous Working Time (Non Stop): 30 Minutes (15 Minutes at 2nd Stages)
  Min. Operation Voltage: DC 11V Max Operation Voltage: DC 14V 
  
  

  Additional Information

  This pump is suitable for the products that are using the Boston type, HR (Halkey-Roberts), Bravo or similar type air valve, Leafield valve etc. This type of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. We have the Pump in Kite version, Please know the Kite version pump also good for Inflatable boats and all application same as the regular pump version.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.
  
  Use for Deflation - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.
  
  

• Pump Operation

  1). Choose the proper fitting for the air valve of your inflatable boat, inflatable kite or paddle board. Put the valve at the inflation position. Attach the correct valve adapter to the inflation hose that comes with your pump. Attach the other end to the pump (smooth round outlet on the pump).
  
  2). Connect the pump’s terminals to the battery paying close attention to the polarity. Make sure the clips are on the same color electrode and properly connected. Otherwise the pump won’t turn on or run properly.
  
  3). Enter the maximum desired pressure by using the set pressure button. The set pressure will be shown on the right hand side of the LCD screen. The pump provides readings in metric (KPa). (Pressure: 10KPa = 100mbr = 1.45 PSI). Factory default working pressure is set at 25KPa (3.6 PSI).This pressure is suitable for most inflatable boats. 45Kpa is 6 PSI to support the inflatable kite.
  
  4). Press the POWER button to start. During inflation, the left hand side of LCD screen should show the pressure that the inflator has reached. As soon as entered set pressure has been reached, the inflator turns off automatically. Take off the air hose from the chamber once the pump stops running. The inflator can be turned off at any time by pressing the POWER button again. It is possible to stop the inflator at any time by pressing this button.
  
  5). The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t be started.

• Warranty

  For recreational use, the electrical control boards, motor, charger are guaranteed for 2 years. Air hose, valve adapters and carrying bag are guaranteed for 6 months. Warranty for commercial use is limited to six months from purchase date.

Boat Cover Support Pole System, Telescopic Pole with 4 Tie Down Straps

40.00 USD

Features

Information about Seamax Inflatable Boat Covers

Bravo Portable Digital Manometer Air Pressure Gauge for Inflatable Boats

49.00 USD

A handy safety equipment helps to check real time air pressure in the boat chambers and ensure the inflatable boat performs to its specification.

Digital LCD display mode: PSI, Kpa, or Bar

Pressure range: 0 to 14.5 psi (0 - 999 mbar)

Resolutions: 10 mbar (0.15 psi)

Power source: 9 Volt DC battery (not included)

Auto shutoff to save battery

Comes with a carrying bag and universal adapters

Cordless Stick and Handheld Electric Floor Mop and Sweeper with 7.4 Volt 1500 mAh Lithium Battery

79.00 USD

• Features
• Specification

• The Seamax Cordless Electric Mop & Sweeper offers the power you need to keep your home clean without the hassle of a cord. Less than 3 pounds weight, easy carrying, washable and fast charging. This new nice looking tool makes it easier than ever to clean up, down and all-around. With multi-floor cleaning performance, you can move from room to room, cleaning both hard floors and light carpet.

  • Ultra low noise motorized soft roller brushing action. No exhaust for better indoor air quality. Washable ultra fine soft fibre roller brush to pickup dust, dirt, crumbs and more. Easy-to-remove magnetic dust compartment for quick clean up.
  • Light weight and ergonomic handle with power and speed controls. No need to bend down to start the device for senior users or patients with lumbar.
  • Two adjustable length: 40” or 20”.  Multi-angle pivoting mop head manoeuvres around furniture and in tight spaces. Low profile mop head for easy accessing to the under furniture space.
  • Cordless, slim, and multi-angle swivel mop head design brings users free floor sweeping and mopping experience. Reduced cleaning and polishing effort on any flat hard surface floors: laminate, vinyl, ceramic, granite, and marble.
  • Interchangeable 7.4V 1500mAh Lithium battery. Long lasting running time. Standard mode: 100 min. High speed mode: 60 min. Rapid charging time: 3 hours. Universal 110 - 240V smart charger. Worry-free one year limited warranty.

• Battery Voltage: 7.4V
  Charger Voltage: 100 - 240V
  Charging Time: 3 hours
  Working Time: standard speed - 100 minutes, high speed – 60 minutes
  Working Noise: 40 - 51db
  Handle Length: 21 inches or 41 inches
  Roller Brush Width: 9 inches
  Mop Head Width: 11 inches
  Net Weight: 3 LBS

DC Trolling Motor Speed Controller for L-Series and X-Series 12V/24V Models - 2016-2017 Model

30.00 USD

Suitable for Seamax Earlier Version of Trolling Motor, Buyer may double check the parts version before purchase. Also see the motor photo image for the related models.

• 8-speed controller (5 forward and 3 reverse)
• Suitable for Seamax L-Series and X-Series 12V Electric Trolling Motor

NOTE: This parts is not suitable for Seamax SpeedMax (2018) and PowerMax (2019) Electric Trolling Motor

DC Trolling Motor Speed Controller for SpeedMax 12V/24V Models - 2017-2018 Model

40.00 USD

Suitable for Seamax SpeedMax DC 12V/24V Electric Trolling Motor, Buyer may double check the parts version before purchase.  Also see the motor photo image for the related models.

• 8-speed controller (5 forward and 3 reverse)
• Suitable for Seamax PowerMax 12V and 24V Electric Trolling Motor

NOTE: This parts is NOT suitable for Seamax X Model and L Model  (2016-2017) and PowerMax (2019) Electric Trolling Motor

Deluxe Boat Launching Dolly, 4 Positions and 4 Stages Removable and Adjustable Legs, 14" Pneumatic Wheels

229.00 USD

• Features
• Description

• Features

  Originally designed with 3D-work by Seamax Marine back in 2011, Now it is the 2nd edition released in 2019.  Seamax Deluxe Boat Launching Wheels system is made by the marine grade T6 aluminum alloy with CNC processing and shiny looking anodized coating against the corrosion.  Thus the product is good for saltwater use.  Small parts are all made by solid stainless steel and reinforced Nylon.  The air filled tire is lab-tested (1000 LBS), and is great to support a MAX loading of 600 LBS in all condition.  A great add-on for inflatable, aluminum and fiberglass boats.
  
  BENEFIT of its new design - With the 4 stages of length and 4 wheel arm position, the dolly can be adjusted while afloat in the boat, leaving or coming into the dock.  The dolly system can also bring different performance positions for boat launching. The wheel arm length increment is 2.5” per stage. Plus the wheel’s diameter, the range of length is 23 - 30 inches.
  
  The wheel arm has 60° and 90° locking position to move up and down. The upper-60° position can free up more space on the top and side of the transom. The lower 60° position lets the wheels run at the same level as the prop, and thus turns the wheels as a prop guard when boat launching.
  
  The transom bracket installation area is about 8 x 3 inches.  Shorter transom bracket design brings more possible installation for all type of boats with different transom. The brackets can be installed at the waterline top position, so to avoid the water comes into the screw holes. We had developed a profile for the transom bracket in 2019. Now the bracket only requires 2 bolts to install. Easier to put it on your boat with the same loading capacity. 
  
  TRIPLE heavy duty, TRIPLE quality! Product is made by Seamax Canada with 2 years limited warranty and 100% Customer Satisfaction guaranteed!  The Quick Operation Features of the Deluxe Boat Dolly include - spring load locking pin for wheel arm position adjustment; solid spring load buttons for wheel arm length adjustment; and quick released lock pin for wheel arm and wheel bearing. 
  
  

  Our new tires are now 14” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

•  Description

  ADJUSTABLE DESIGN: These wheels have 4 adjustment positions for length and angle to adjust the leg length, push in the spring-loaded buttons on each side of the leg and either pull or push to lengthen or shorten. To adjust the leg angle, push down on the spring-loaded bar near the top of the leg assembly and move the leg assembly to the desired location. To remove the leg assembly from the bracket, pull out the quick release pin located at the top of the leg assembly.
  
  MAX LOAD: This dolly set is designed for boats with solid outboard transom. For easier moving, total weight should not exceed 600 Lbs including boat, outboard, and all gears.
  
  INSTALLATION: This dolly set should only be installed by an adult with some experience in working with tools. To install the wheelset properly, you will need to drill 5/16” holes in the plywood transom for the mounting brackets. It is very important to locate the position of the holes correctly. Please check carefully including checking the wheel arm position before starting to drill any holes.
  
  MAINTENANCE: Wash it after using it from saltwater or sandy beach. Check tire pressure before every using. Don’t store the wheels under the sun or beside the heat to maximize its lifetime. Take the wheel arm off from the transom bracket when storing your boat. Lube the spring load dolly system if needed. Always keep the lock pin on the dolly bracket.
  
  TIRE INFLATION: Dolly tires may not be fully inflated when shipping; please only give 15-20 PSI pressure at room temperature before using. Best to use a car tire digital air pump to prevent tire over-inflation. Tire over-inflated will cause damage and the warranty is not covered.
  
  14" Dual wheel upgrade kit is available for this Deluxe boat launching wheelset for heavy loading application or sandy beach use. We suggest the boat 14ft and up to use this upgrade kit, then you can have a wide enough transom to support 4 wheels operation.
  
  WARRANTY: Manufacturer 2 years Parts Limited Warranty within USA & Canada. 60 days free replacement on any defective components. Please take photos or return the product or parts to the retailer you purchased them from if there is a warranty issue. You can also contact Seamax for technical support. 
  

Deluxe Bow Bag for Inflatable Boats

55.00 USD

Features

• Water resistant padded material. 600D Polyester coated PVC
• 4 adjustable tie down straps with marine grade nylon quick release hooks
• 2 Ways webbing handles
• Multiple sizes to fit all inflatable boats

Drain Valve - Hexagon Style for 1" or 1-1/2" Thick Transom with Sikaflex 291i Marine Sealant

45.00 USD

Hexagon drain valve for 1" or 1-1/2" transom

Package contents: 1x drain valve, 1x Sikaflex 291i marine sealant 3.5oz tube.

General Instruction of Drain Valve Replacement

1) First remove the old drain valve and check the drain valve hole on the transom to make sure the new drain valve matches the hole dimensions.  Then clean up all the dirt from the hole. If there is water in the drain hole, wash it again and leave it dry in the air. Make sure all the condition are good before starting to install the new drain valve.

2) Put the Sikaflex 291i on the drain hole surface about 1mm thickness (5-15g). Wear a glove and use a finger to push the sealant fully coated at the drain hole. Wait 30-60 minutes to let the new sealant coating stay well before putting the new drain valve in.

3) Apply about 5 g of the Sikaflex 291i on the valve and transom contact surface before installation. It helps the valve to get perfect water tight result.

4) Many inflatable boats come with plywood transom with wrong sealant used in the factory. The waterproof coating need to be refinished. Boat's old drain valve may have already caused some water leaking and damage to the transom. This Sikaflex sealant perfectly helps to finish the replacement.

General Instruction of Sikaflex 291i (100g pack):

Professional grade marine adhesive/ sealant used by boat builders and yards to bond and bed boat components structurally. Fast strength build-up overnight. Use above and below the waterline. Comes with nozzle. All purpose adhesive sealant, bond to hull and structural members. Bedding compound, light bonding, fast-cure polyurethane sealant. 

If a partial pack remains, you can simply squeeze the air out of the tube using the included tool, thereby extending the shelf life of opened product. Includes application nozzle and dispensing/ storage tool.

Drain Valve - Pull-Up Style for 1" or 1-1/2" Thick Transom with Sikaflex 291i Marine Sealant

45.00 USD

Pull-Up for Transom with thickness of 1" or 1-1/2"

The order set includes: 1x Drain Valve. 1x Sikaflex 291i marine sealant, 3.5oz tube.

General Instruction of Drain Valve Replacement

1) First remove the old drain valve and check the drain valve hole on the transom to make sure the new drain valve matches the hole dimensions.  Then clean up all the dirt from the hole. If there is water in the drain hole, wash it again and leave it dry in the air. Make sure all the condition are good before starting to install the new drain valve.

2) Put the Sikaflex 291i on the drain hole surface about 1mm thickness (5-15g). Wear a glove and use a finger to push the sealant fully coated at the drain hole. Wait 30-60 minutes to let the new sealant coating stay well before putting the new drain valve in.

3) Apply about 5 g of the Sikaflex 291i on the valve and transom contact surface before installation. It helps the valve to get perfect water tight result.

4) Many inflatable boats come with plywood transom with wrong sealant used in the factory. The waterproof coating need to be refinished. Boat's old drain valve may have already caused some water leaking and damage to the transom. This Sikaflex sealant perfectly helps to finish the replacement.

General Instruction of Sikaflex 291i (100g pack):

Professional grade marine adhesive/ sealant used by boat builders and yards to bond and bed boat components structurally. Fast strength build-up overnight. Use above and below the waterline. Comes with nozzle. All purpose adhesive sealant, bond to hull and structural members. Bedding compound, light bonding, fast-cure polyurethane sealant. 

If a partial pack remains, you can simply squeeze the air out of the tube using the included tool, thereby extending the shelf life of opened product. Includes application nozzle and dispensing/ storage tool.

Easy-Load Boat Launching Wheels Set for Inflatable Boat and Aluminum Boat, 2 Height Positions, 12" Pneumatic Wheels

138.00 USD

• Features
• Installation

• Features

  Seamax Easy Load Boat Launching Wheels Set is designed by Seamax Canada, made with the hardest marine grade T6 aluminum alloy with CNC processing. Shiny looking anodized coating on all aluminum parts, product is good for saltwater using; Small parts are all made by solid stainless steel. Lab 1000 LBS tested, support MAX 500 LBS loading in all condition, good for inflatable boats, aluminum boats and fiberglass boats.
  
  This system is designed for boats with transom, the length of the boat should not exceed 16 FT and the total weight is within 500 LBS. These transom wheels should only be installed by an adult with some experience in working with tools. To install the wheel set properly, first drill 4 holes (5/16”) in the transom for the mounting. Addition reinforcement may be required on some aluminum transom. And you can use marine sealant and suggested Sikaflex 291.
  
  Benefit from its new Push Button design and 3-stages wheel arm, the system can be adjusted while afloat in the boat leaving or coming into dock. It can also bring different performance position for boat launching. The wheel arm length increment is 2.5” per stage, plus the wheel’s diameter, the range of length is 22 - 28 inches.
  
  Tire inflation: Dolly tires may not be fully inflated when shipping; please only give 15 - 20 PSI pressure at room temperature before using. Best to use portable type digital air pump in case tire over inflated. Tire over inflated will cause damage and the warranty is not covered. Dual wheel kit is available for this dolly for heavy loading application.
  
  Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.
  
  Maintenance: Wash it after using from salt water or sandy beach. Check tire pressure before every using. Don’t store the wheels under the sun or beside the heat to maximize its life time. Take the wheel arm off from the transom bracket when store your boat. Lube the spring load dolly system is necessary. Keep the lock pin on the dolly bracket. Manufacturer 2 years Parts Limited Warranty within USA & Canada. 30 days free replacement on any defective transom wheel sets.
  
  

• Installation

  These wheels have 2+1 adjustment positions for length base on the wheel arm end rotation position upper or lower. to remove the leg assembly from the bracket, simply push the stainless steel locking button and then the rotation button to release.
  
  The wheels must face towards the boat tubes and be as far apart as possible (it brings more stability when moving the boat around) and clear the boat tubes by about one inch so they don't rub against the tubes when being raised or lowered. The wheels must also clear from the bottom of the boat by about one inch when placed in their lowered position.
  
  Once you have determined the mounting positions for the brackets which should be straight up and down on the transom and about 6-8 inches up from the bottom of the bracket to the bottom of the boat.  Mark where to drill the 5/16” holes (drill bit not included). This is best done by separating the leg assembly from the bracket. Double check everything again before drilling any holes!  Holes and transom must be vertical.
  
  Use the supplied washers and lock nuts on the bolts on the inside of the transom to secure the brackets to the transom and then cap them with the supplied acorn nuts to protect your boat when rolled up.

End Cap Set of 2 Pair for Aluminum Side Joiner Bar of Inflatable Boat

28.00 USD

2 Pair of Marine grade plastic end cap set for aluminum floor side joiner.

Pack contents: 2x left side end cap, 2x right side end cap

Color: black 

Extra Bracket Set for Seamax Deluxe Launching Wheels

99.00 USD

2 x Aluminium Bracket

Suitable for Seamax Deluxe Launching Wheels

Installation stainless steel bolts and nuts included

Extra Bracket Set for Seamax Easy Load Launching Wheels

69.00 USD

2 x Marine Grade Aluminium Bracket

Suitable for Seamax Easy Load Launching Wheels

Installation stainless steel bolt and nuts included

Fishing Rod Holder: Bench Seat Mounting Dual Nylon Holders with 12" Aluminum Track

85.00 USD

Package contents: 2x durable nylon deluxe fishing rod holder, 1x adjustable 12" bench seat mounting track assembly

All angle tillable and rotatable holder. Movable base along the seat mounting track.

Fishing Rod Holder: Transom Mounting All Angle Nylon Holder with Aluminum 2-1/2" Clamp

55.00 USD

- Adjustable aluminum transom mounting clamp base. Max 2-1/2" opening.

- Durable nylon fabric reinforced holder assembly

- Tillable and rotatable holder head

 - Quick fishing rod locking ring. Solid and Durable

Foldable Inflatable Boat Hull Storage and Carrying Bag

Sold Out

Features

• Water proof material. 600D Polyester coated PVC
• 2 Horizontal + 3 Vertical tie down straps with D-rings
• Flexible and easy to pack the boat up, side pocket included
• 2 Ways webbing handle and carrying strap, Easy to Move
• Multiple sizes, Seamax certified quality, fit all inflatable boats
• Size A for folding hull size approx. (45" x 25" x 13")
• Size B for folding hull size approx. (50" x 27" x 15") 
• Size C for folding hull size approx. (57" x 29" x 17")
• Size D for folding hull size approx. (65" x 32" x 19")

Inflatable Boat Cover, A Series for Beam 4.3 - 4.6 FT, 3 Sizes fit Length 6.9 - 8.7 FT

63.00 USD

• Descriptions
• Model Check List
• Additional Info

• Descriptions

  SIZE -  A Series inflatable boat cover fits boats with beam between 4.3 FT to 4.6 FT. There are 3 models in A series: A210 fits Max Length 6.9 FT boat; A240 fits Max Length 7.9 FT boat; A265 fits Max Length 8.7 FT boat.
  
  MOTOR WELL STYLE & TRAILERABLE - Seamax boat cover should be able to cover your boat and the motor; the covers have been designed to fit the boat and its max rating outboard motor. Fabric is Water repellent, mildew and UV resistant with Density 600D/260g/SQM; Elastic string design for quick fitted and released; Multiple Tie-Down Loops built-in; free cover carrying bag included. Max trailer Road Speed 65 km/ hour (40 miles/ hour), additional tie-down core will be required.
  
  FULL SUPPORT - Seamax inflatable boat covers have 6 series and overall 25 models. Our boat covers can fit the inflatable boats from 6.5 FT to 20 FT. Each series includes couple of sizes for different tube styles & boat length. Our boat cover sizes under a same series should be with the same width. The bow style will not affect the cover size in most cases.
  
  MODEL CHECK LIST - If you have an Achilles, Mercury, Seamax or Zodiac inflatable boat, you can find your boat cover model from below Check List. Factor in the dimensions of additional features or boat style could affect the cover such as rounded pontoon cone end or tall center console. Please allow a few inches of additional length to fit your additional boat equipment when picking the cover.
  
  UNIVERSAL COVER - No matter which brand of boat you have, even if it is a RIB with a console, our universal cover should fit as long as your inflatable boat has a built-in transom.

• Model Check List

  SEAMAX BOAT COVER MODEL LIST (BOAT# -- COVER# / 2015)

  Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model.

  
  -- ACHILLES
  LT2-A265 LT4-B295 LS2-A240 LS4-B270
  LEX: LEX77-B255 LEX88-B270 LEX96-B295
  LSR: LSR290-B320 LSR310-B350
  LSI: LSI230-B255 LSI260-B295 LSI290-B320 LSI310-B350 LSI335-C360 LSI365-C420
  SPD: SPD290-B320 SPD310-B350 SPD335-C390 SPD365-C420
  RIGID HB-FX: 270FX-B295 300FX-C330
  RIGID HB-LX: 240LX-B255 280LX-C300 315LX-C360 350LX-D400
  RIGID HB-DX WITH SEAT & CONSOLE: HB280DX-C330 HB315DX-C360 HB350DX-D400
  FOLDABLE: SG124-C390 SG140-D430 SG156-D500 SU14-D430 SU16-E500 SU18-E600
  *
  -- MERCURY
  DINGHY: 200-A210 240-A240 270-A265
  ROLL UP: 240-B270
  SPORT & ADVENTURE SPORT: 240-B270 270-B290 310-B320 340-B350
  AIR DECK (PVC/HP): 240-B270 270-B290 310-B320 340-B350
  DYNAMIC: RIB260-B295 RIB280-B320 RIB310-B350
  SEA RUNNER: 300-C300 350-C360 430-D430
  HEAVY DUTY: 380-D430 430-D4500
  AMANZI: 350-D430 400-E460
  *
  -- SEAMAX
  AIR: 230-A240 270-B270 320-B320
  HD: 330-B350 360-C390 380-C420 430-D470 470-D500
  OCEAN: 290-B295 320-B320 380-C390 430-D430
  OCEAN-T: 380T-C390 430T-C430 500T-E500
  SPORT EMARINE: 240-B240 270-B270 305-B320 365-C360 420-D430
  *
  -- ZODIAC
  PROJET: 350TC4-D400 420TC4-D430
  YACHTLINE DELUXE: YL340DL-C390 YL380DL-C420 YL420DL-D500 YL470DL-E550 YL530DL-E600
  CADET: RIB220-B255 RIB260-C300 RIB310-C360 RIB340-D400
  COMPACT: COMPACT250-C300 COMPACT300-C330
  CADET FASTROLLER ACTI-V: FR285-C330 FR325-C360 FR360-C390
  CADET ROLL UP: 200-B255 240-V270 260-B295
  CADET SOLID: 260S-C300 285S-C330 310S-C360 340S-D400
  CADET AIRLITE: 240-B270 260-C300
  ZOOM: 230-A265 260AERO-B295 260S-B295 310S-B350 350S-C420
  BOMBARD TYPHOON ROLL-UP/AERO: 200-A210 235-A240 265-A265 310-B320 360-c360
  
  

• Additional Info

  Boat Measurement - Measure in a straight line (down the center of the boat), Factor in the dimensions of any additional features that will affect the cover such as a trolling motor, center console, jack plate or aftermarket pulpit or anchor davit that is not listed in this manual.
  
  Note: Please allow a few inches of additional length to fit that equipment when picking the cover. - If you have a swim step, measure next from the tip of the bow to the back center of your swim platform. This is in addition to the first center line length because some covers will fit a step and others will not so you will want to have both measurements to ensure the right selection.
  
  Tips 1: Inflatable boat with round cone end & console will need extra length counted. Tips 2: Please contact Seamax if you need more help to pick the size.
  
  If you pick a wrong size boat cover, that is no problem, we have our Express Replacement service to help you out from this issue. You can let us know your boat model, dimensions, pictures & with a short description. We will ship you a new model including an UPS return shipping waybill. Additional cost may be applied.

Inflatable Boat Cover, B Series for Beam 4.7 - 5.2 FT, 5 Sizes fit Length 8.3 - 11.5 FT

80.00 USD

• Descriptions
• Model Check List
• Additional Info

• Descriptions

  SIZE - The inflatable boat with beam between 4.7 to 5.2 FT should choose B Series cover. There are 5 models in B series: B255 fits 7.5 - 8.3 FT boat; B270 fits 8.4 - 9 FT boat; B295 fits 9.1 - 9.7 FT boat; B320 fits 9.8 - 10.5 FT boat; B350 fits 10.6 - 11.5 FT boat.
  
  MOTOR WELL STYLE & TRAILERABLE - Our boat cover should be able to cover your boat and the motor. The covers have been designed to fit the boat and its max rating outboard motor. Fabric Specs - Water repellent, mildew and UV resistant. Density 600D/260g/SQM. Elastic string design for quick fitted and released. Multiple Tie-Down Loops built-in.  Free cover carrying bag included. Max trailer road speed 65 km/ hour (40 miles/ hour), additional tie-down core will be required.
  
  FULL SUPPORT - Seamax inflatable boat covers have 6 series and overall 25 models. Seamax boat covers fit the inflatable boats from 6.5 FT to 20 FT. Each series includes several sizes for different tube styles and boat length. Our boat cover sizes under a same series should be with the same width. The bow style will not affect the cover size in most cases.
  
  MODEL CHECK LIST - For Achilles, Mercury, Seamax or Zodiac inflatable boat, search the suitable boat cover model from the below Check List. Factor in the dimensions of additional features or boat style such as rounded pontoon cone end or tall center console, it affects the cover sizes. Please allow a few inches of additional length to fit your additional boat equipment when picking the cover.
  
  UNIVERSAL COVER - No matter which brand of boat you have, even if it is a RIB with a console, Seamax's universal boat cover should fit as long as your inflatable boat has a built-in transom.

• Model Check List

  SEAMAX BOAT COVER MODEL LIST (BOAT# -- COVER# / 2015)

  Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model.

  
  -- ACHILLES
  LT2 (A265) / LT4 (B295) / LS2 (A240) / LS4 (B270)
  LEX: LEX77 (B255) / LEX88 (B270) / LEX96 (B295)
  LSR: LSR290 (B320) LSR310 (B350)
  LSI: LSI230 (B255) / LSI260 (B295) / LSI290 (B320) / LSI310 (B350) / LSI335 (C360) / LSI365 (C420)
  SPD: SPD290 (B320) / SPD310 (B350) / SPD335 (C390) / SPD365 (C420)
  RIGID HB-FX: 270FX (B295) / 300FX (C330)
  RIGID HB-LX: 240LX (B255) / 280LX (C300) / 315LX (C360) 350LX (D400)
  RIGID HB-DX WITH SEAT & CONSOLE: HB280DX (C330) / HB315DX (C360) / HB350DX (D400)
  FOLDABLE: SG124 (C390) / SG140 (D430) / SG156 (D500) / SU14 (D430) / SU16 (E500) / SU18 (E600)
  *
  -- MERCURY
  DINGHY: 200 (A210) / 240 (A240) 270 (A265)
  ROLL UP: 240 (B270)
  SPORT & ADVENTURE SPORT: 240 (B270) / 270 (B290) / 310 (B320) / 340 (B350)
  AIR DECK (PVC/HP): 240 (B270) / 270 (B290) / 310 (B320) / 340 (B350)
  DYNAMIC: RIB260 (B295) / RIB280 (B320) / RIB310 (B350)
  SEA RUNNER: 300-C300 350-C360 430-D430
  HEAVY DUTY: 380 (D430) / 430 (D450)
  AMANZI: 350 (D430) / 400 (E460)
  *
  -- SEAMAX
  AIR: 230 (A240) / 270 (B270) / 320 (B320)
  HD: 330 (B350) / 360 (C390) / 380 (C420) / 430 (D470) / 470 (D500)
  OCEAN: 290 (B295) / 320 (B320) / 380 (C390) / 430 (D430)
  OCEAN-T: 380T (C390) /  430T (C430) / 500T (E500)
  SPORT EMARINE: 240 (B240) /  270 (B270) / 305 (B320) / 365 (C360) / 420 (D430)
  *
  -- ZODIAC
  PROJET: 350TC4 (D400) / 420TC4 (D430)
  YACHTLINE DELUXE: YL340DL (C390) / YL380DL (C420) / YL420DL (D500) / YL470DL (E550) / YL530DL (E600)
  CADET: RIB220 (B255) / RIB260 (C300) / RIB310 (C360) / RIB340 (D400)
  COMPACT: COMPACT250 (C300) / COMPACT300 (C330)
  CADET FASTROLLER ACTI-V: FR285 (C330) / FR325 (C360) / FR360 (C390)
  CADET ROLL UP: 200 (B255) / 240 (B270) / 260 (B295)
  CADET SOLID: 260S (C300) / 285S (C330) / 310S (C360) / 340S (D400)
  CADET AIRLITE: 240 (B270) / 260 (C300D
  ZOOM: 230 (A265) / 260AERO (B295) / 260S (B295) / 310S (B350) 350S (C420)
  BOMBARD TYPHOON ROLL-UP/AERO: 200 (A210) / 235 (A240) / 265 (A265) / 310 (B320) / 360 (C360) 
  
  

• Additional Info

  Boat Measurement - Measure in a straight line (down the center of the boat), Factor in the dimensions of any additional features that will affect the cover such as a trolling motor, center console, jack plate or aftermarket pulpit or anchor davit that is not listed in this manual.
  
  Note: Please allow a few inches of additional length to fit that equipment when picking the cover. - If you have a swim step, measure next from the tip of the bow to the back center of your swim platform. This is in addition to the first center line length because some covers will fit a step and others will not so you will want to have both measurements to ensure the right selection.
  
  Tips 1: Inflatable boat with round cone end & console will need extra length counted. Tips 2: Please contact Seamax if you need more help to pick the size.
  
  If you pick a wrong size boat cover, that is no problem, we have our Express Replacement service to help you out from this issue. You can let us know your boat model, dimensions, pictures & with a short description. We will ship you a new model including an UPS return shipping waybill. Additional cost may be applied.

Inflatable Boat Cover, C Series for Beam 5.3-5.7ft, 5 Sizes fit Length 9.9-13.8ft

105.00 USD

• Descriptions
• Model Check List
• Additional Info

• Descriptions

  SIZE - C SERIES INFLATABLE BOAT COVER – fits Beam between 5.3ft to 5.7ft. There are 5 models in C series: C300 fits Max Length 9.9ft boat; C330 fits Max Length 10.8ft boat; C360 fits Max Length 11.8ft boat; C390 fits Max Length 12.8ft boat; C420 fits Max Length 13.8ft boat.
  
  MOTOR WELL STYLE & TRAILERABLE - Our boat cover should be able to cover your boat and the motor. the covers have been designed to fit the boat and its max rating outboard motor. Fabric Specs - Water repellent, mildew and UV resistant; Density 600D/260g/SQM. Elastic string design for quick fitted and released, Multiple Tie-Down Loops built-in, free cover carrying bag included. Max trailer Road Speed 65km / hour (40mile / hour), additional tie-down core will be required.
  
  FULL SUPPORT - Seamax inflatable boat covers have 6 series and overall 25 models. Our boat covers can fit the inflatable boats from 6.5ft to 20ft. Each series includes couple of sizes for different tube styles & boat length. Our boat cover sizes under a same series should be with the same width. The bow style will not affect the cover size in most cases.
  
  MODEL CHECK LIST - If you have an Achilles, Mercury, Seamax or Zodiac inflatable boat, you can find your boat cover model from below Check List. Factor in the dimensions of additional features or boat style could affect the cover such as rounded pontoon cone end or tall center console. Please allow a few inches of additional length to fit your additional boat equipment when picking the cover.
  
  UNIVERSAL COVER - No matter which brand of boat you have, even if it is a RIB with a console, our universal cover should fit as long as your inflatable boat has a built-in transom.

• Model Check List

  SEAMAX BOAT COVER MODEL LIST (BOAT# -- COVER# / 2015)

  Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model.

  
  -- ACHILLES
  LT2-A265 LT4-B295 LS2-A240 LS4-B270
  LEX: LEX77-B255 LEX88-B270 LEX96-B295
  LSR: LSR290-B320 LSR310-B350
  LSI: LSI230-B255 LSI260-B295 LSI290-B320 LSI310-B350 LSI335-C360 LSI365-C420
  SPD: SPD290-B320 SPD310-B350 SPD335-C390 SPD365-C420
  RIGID HB-FX: 270FX-B295 300FX-C330
  RIGID HB-LX: 240LX-B255 280LX-C300 315LX-C360 350LX-D400
  RIGID HB-DX WITH SEAT & CONSOLE: HB280DX-C330 HB315DX-C360 HB350DX-D400
  FOLDABLE: SG124-C390 SG140-D430 SG156-D500 SU14-D430 SU16-E500 SU18-E600
  *
  -- MERCURY
  DINGHY: 200-A210 240-A240 270-A265
  ROLL UP: 240-B270
  SPORT & ADVENTURE SPORT: 240-B270 270-B290 310-B320 340-B350
  AIR DECK (PVC/HP): 240-B270 270-B290 310-B320 340-B350
  DYNAMIC: RIB260-B295 RIB280-B320 RIB310-B350
  SEA RUNNER: 300-C300 350-C360 430-D430
  HEAVY DUTY: 380-D430 430-D4500
  AMANZI: 350-D430 400-E460
  *
  -- SEAMAX
  AIR: 230-A240 270-B270 320-B320
  HD: 330-B350 360-C390 380-C420 430-D470 470-D500
  OCEAN: 290-B295 320-B320 380-C390 430-D430
  OCEAN-T: 380T-C390 430T-C430 500T-E500
  SPORT EMARINE: 240-B240 270-B270 305-B320 365-C360 420-D430
  *
  -- ZODIAC
  PROJET: 350TC4-D400 420TC4-D430
  YACHTLINE DELUXE: YL340DL-C390 YL380DL-C420 YL420DL-D500 YL470DL-E550 YL530DL-E600
  CADET: RIB220-B255 RIB260-C300 RIB310-C360 RIB340-D400
  COMPACT: COMPACT250-C300 COMPACT300-C330
  CADET FASTROLLER ACTI-V: FR285-C330 FR325-C360 FR360-C390
  CADET ROLL UP: 200-B255 240-V270 260-B295
  CADET SOLID: 260S-C300 285S-C330 310S-C360 340S-D400
  CADET AIRLITE: 240-B270 260-C300
  ZOOM: 230-A265 260AERO-B295 260S-B295 310S-B350 350S-C420
  BOMBARD TYPHOON ROLL-UP/AERO: 200-A210 235-A240 265-A265 310-B320 360-c360
  
  

• Additional Info

  Boat Measurement - Measure in a straight line (down the center of the boat), Factor in the dimensions of any additional features that will affect the cover such as a trolling motor, center console, jack plate or aftermarket pulpit or anchor davit that is not listed in this manual.
  
  Note: Please allow a few inches of additional length to fit that equipment when picking the cover. - If you have a swim step, measure next from the tip of the bow to the back center of your swim platform. This is in addition to the first centerline length because some covers will fit a step and others will not so you will want to have both measurements to ensure the right selection.
  
  Tips 1: Inflatable boat with round cone end & console will need extra length counted. Tips 2: Please contact Seamax if you need more help to pick the size.
  
  If you pick a wrong size boat cover, that is no problem, we have our Express Replacement service to help you out from this issue. You can let us know your boat model, dimensions, pictures & with a short description. We will ship you a new model including an UPS return shipping waybill. Additional cost may be applied.