Launching Wheels

Portable Boat Carry and Launching Hand Dolly Set, 16” Pneumatic Wheels

279.00 USD

Features

Easy-Load Boat Launching Wheels Set for Inflatable Boat and Aluminum Boat, 2 Height Positions, 12" Pneumatic Wheels

168.00 USD

• Features
• Installation

• Features

  Seamax Easy Load Boat Launching Wheels Set is designed by Seamax Canada, made with the hardest marine grade T6 aluminum alloy with CNC processing. Shiny looking anodized coating on all aluminum parts, Product is good for saltwater using; Small parts are all made by solid stainless steel. Lab 1000 LBS tested, support MAX 500 LBS loading in all conditions, good for inflatable boats, aluminum boats, and fiberglass boats.
  
  This system is designed for boats with transom, the length of the boat should not exceed 16 FT and the total weight is within 500 LBS. These transom wheels should only be installed by an adult with some experience in working with tools. To install the wheelset properly, first drill 4 holes (5/16”) in the transom for the mounting. Additional reinforcement may be required on some aluminum transom. And you can use marine sealant and suggested Sikaflex 291 or 3M 5200.
  
  Benefit from its new Push Button design and 3-stages wheel arm, the system can be adjusted while afloat in the boat leaving or coming into dock. It can also bring different performance positions for boat launching. The wheel arm length increment is 2.5” per stage, plus the wheel’s diameter, the range of length is 22 - 28 inches.
  
  Tire inflation: Dolly tires may not be fully inflated when shipping; please only give 15 - 20 PSI pressure at room temperature before using. Best to use portable type digital air pump in case of tire over-inflated. Tire over inflated will cause damage and the warranty is not covered. Dual wheel kit is available for this dolly for heavy loading application.
  
  Our new tires are now 12” in diameter and about 4” wide. They are made of 4 plies reinforced vehicle grade natural rubber which holds up well against UV rays, heat and saltwater for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high-quality marine-grade tires and rims will last you for many years of trouble-free use.
  
  Word Wide Buyer
  Australia and New Zealand -  visit www.amazon.com.au
  UK and other Europe Countries - visit www.amazon.co.uk.
  
  Maintenance: Wash by freshwater after using it from saltwater or sandy beach. Check tire pressure before every use. Don’t store the wheels under the sun or beside the heat to maximize its lifetime. Take the wheel arm off from the transom bracket when storing your boat. Lube the spring load dolly system is necessary. Keep the lock pin on the dolly bracket. Manufacturer 2 years Parts Limited Warranty within USA & Canada. 30 days free replacement on any defective transom wheelsets.
  
  

• Installation

  These wheels have 2+1 adjustment positions for length base on the wheel arm end rotation position upper or lower. to remove the leg assembly from the bracket, simply push the stainless steel locking button and then the rotation button to release.
  
  The wheels must face towards the boat tubes and be as far apart as possible (it brings more stability when moving the boat around) and clear the boat tubes by about one inch so they don't rub against the tubes when being raised or lowered. The wheels must also clear from the bottom of the boat by about one inch when placed in their lowered position.
  
  Once you have determined the mounting positions for the brackets which should be straight up and down on the transom and about 6-8 inches up from the bottom of the bracket to the bottom of the boat.  Mark where to drill the 5/16” holes (drill bit not included). This is best done by separating the leg assembly from the bracket. Double-check everything again before drilling any holes!  Holes and transom must be vertical.
  
  Use the supplied washers and lock nuts on the bolts on the inside of the transom to secure the brackets to the transom and then cap them with the supplied acorn nuts to protect your boat when rolled up.

2 x 12" Marine Grade Pneumatic Wheels for Seamax Boat Launching Dolly (one pair)

59.00 USD

Suitable for 12" Wheel Version Seamax Boat Launching Wheels Set (All models with 1" diameter axle)

Wheel Model: 4.10/3.50-6

Max Tire Diameter: 12 inches

Wheel Axle Diameter: 1 inch

Suggested Air Pressure:  12 to 15 PSI  (Max 30PSI)

Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

Note: Not intended for highway use. Rinse the product with fresh water after use in salt water. Cover from sun light when no in use and maximize the life time.

Deluxe Boat Launching Dolly, 4 Positions and 4 Stages Removable and Adjustable Legs, 14" Pneumatic Wheels

239.00 USD

• Features
• Description

• Features

  Originally designed with 3D-work by Seamax Marine back in 2011, Now it is the 2nd edition released in 2019.  Seamax Deluxe Boat Launching Wheels system is made by the marine grade T6 aluminum alloy with CNC processing and shiny looking anodized coating against the corrosion.  Thus the product is good for saltwater use.  Small parts are all made by solid stainless steel and reinforced Nylon.  The air-filled tire is lab-tested (1000 LBS), and is great to support a MAX loading of 600 LBS in all condition.  A great add-on for inflatable, aluminum, and fiberglass boats.
  
  BENEFIT of its new design - With the 4 stages of length and 4 wheel arm position, the dolly can be adjusted while afloat in the boat, leaving or coming into the dock.  The dolly system can also bring different performance positions for boat launching. The wheel arm length increment is 2.5” per stage. Plus the wheel’s diameter, the range of length is 23 - 30 inches.
  
  The wheel arm has a 60° and 90° locking position to move up and down. The upper-60° position can free up more space on the top and side of the transom. The lower 60° position lets the wheels run at the same level as the prop, and thus turns the wheels as a prop guard when boat launching.
  
  The transom bracket installation area is about 8 x 3 inches.  Shorter transom bracket design brings more possible installation for all types of boats with different transom. The brackets can be installed at the waterline top position, so to avoid the water comes into the screw holes. We had developed a profile for the transom bracket in 2019. Now the bracket only requires 2 bolts to install. Easier to put it on your boat with the same loading capacity. 
  
  TRIPLE heavy-duty, TRIPLE quality! Product is made by Seamax Canada with 2 years limited warranty and 100% Customer Satisfaction guaranteed!  The Quick Operation Features of the Deluxe Boat Dolly include - spring load locking pin for wheel arm position adjustment; solid spring load buttons for wheel arm length adjustment; and quick released lock pin for wheel arm and wheel bearing. 
  
  

  Our new tires are now 14” in diameter and about 4” wide. They are made of 4 plies reinforced vehicle grade natural rubber which holds up well against UV rays, heat and saltwater for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high-quality marine-grade tires and rims will last you for many years of trouble-free use。
  
  Word Wide Buyer
  Australia and New Zealand -  visit www.amazon.com.au
  UK and other Europe Countries - visit www.amazon.co.uk

•  Description

  ADJUSTABLE DESIGN: These wheels have 4 adjustment positions for length and angle to adjust the leg length, push in the spring-loaded buttons on each side of the leg and either pull or push to lengthen or shorten. To adjust the leg angle, push down on the spring-loaded bar near the top of the leg assembly, and move the leg assembly to the desired location. To remove the leg assembly from the bracket, pull out the quick release pin located at the top of the leg assembly.
  
  MAX LOAD: This dolly set is designed for boats with solid outboard transom. For easier moving, total weight should not exceed 600 Lbs including boat, outboard, and all gears.
  
  INSTALLATION: This dolly set should only be installed by an adult with some experience in working with tools. To install the wheelset properly, you will need to drill 5/16” holes in the plywood transom for the mounting brackets. It is very important to locate the position of the holes correctly. Please check carefully including checking the wheel arm position before starting to drill any holes.
  
  MAINTENANCE: Wash it after using it from saltwater or sandy beach. Check tire pressure before every use. Don’t store the wheels under the sun or beside the heat to maximize its lifetime. Take the wheel arm off from the transom bracket when storing your boat. Lube the spring load dolly system if needed. Always keep the lock pin on the dolly bracket.
  
  TIRE INFLATION: Dolly tires may not be fully inflated when shipping; please only give 15-20 PSI pressure at room temperature before using. Best to use a car tire digital air pump to prevent tire over-inflation. Tire over-inflated will cause damage and the warranty is not covered.
  
  14" Dual wheel upgrade kit is available for this Deluxe boat launching wheelset for heavy loading application or sandy beach use. We suggest the boat 14ft and up to use this upgrade kit, then you can have a wide enough transom to support 4 wheels operation.
  
  WARRANTY: Manufacturer 2 years Parts Limited Warranty within USA & Canada. 60 days of free replacement on any defective components. Please take photos or return the product or parts to the retailer you purchased them from if there is a warranty issue. You can also contact Seamax for technical support. 
  

Stainless Steel Transom Launching Dolly, Easy Removable Legs, 12" Pneumatic Wheels

158.00 USD

• Features
• Installation

• Features

  The Seamax Stainless Steel Transom Launching Wheels set is designed by Seamax Canada for inflatable boats, aluminum boats and fiberglass boats. Durable transom brackets, legs, and installation hardware are good for use in saltwater and fresh water. Max support 500 LBS loading in all condition.
  
  Benefit from its spring loaded wider hand pull bar for easy leg attachment and removal. Fast setting leg to down position for launching or up position during boating. 
  
  Wheel diameter: 12"
  Arm length: 22"
  Bracket Size: L6" x W1.5"
  
  Tire inflation: Dolly tires may not be fully inflated when shipping; please only give 15 - 18 PSI pressure at room temperature before using. Best to use portable type digital air pump to avoid over inflation. Over inflated tires will cause damage to the wheels and will not be covered by the limited.
  
  Maintenance: Check tire pressure before use. Rinse with fresh water after each use. Lubricate the spring loaded bar and axis. To maximize product longevity, store the wheels in a cool and shaped area away from heat, direct sunlight, and UV. 2-years manufacturer limited warranty within USA & Canada. 30 days free replacement on any defective ransom wheel sets.
  
  

• Installation

  These transom wheels should only be installed by an adult with some experience in working with power tools. To install the wheel set properly, first drill 2 holes (5/16”) in the transom for the mounting each bracket. Addition reinforcement may be required in some aluminum transom. Use marine sealant such as Sikaflex 291 to seal the gaps. Clip the wheel legs onto the brackets one by one. 
  
  The wheels must face towards the boat tubes and be as far apart as possible (it brings more stability when moving the boat around) and clear the boat tubes by about one inch so they don't rub against the tubes when being raised or lowered. The wheels must also clear from the bottom of the boat by about one inch when placed in their lowered position.
  
  Once you have determined the mounting positions for the brackets which should be straight up and down on the transom and about 6-8 inches up from the bottom of the bracket to the bottom of the boat.  Mark where to drill the 5/16” holes (drill bit not included). This is best done by separating the leg assembly from the bracket. Double check everything again before drilling any holes!  Holes and transom must be vertical.
  
  Use the supplied washers and lock nuts on the bolts on the inside of the transom to secure the brackets to the transom and then cap them with the supplied acorn nuts to protect your boat when rolled up.

12" Dual Wheel Upgrade Kit for Seamax EZ Load, and 2017 Deluxe Launching Wheel or Earlier

79.00 USD

Provide a 4-Wheels system option to "Deluxe Launching Wheels 2017 or Earlier Model" and "Easy Load Launching Wheels". (12" Wheel Version)

Suggested for larger boat with wider transom. Provide better support on soft terrain and sandy beach.

Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

Package includes: 2 x 12 inches Pneumatic tire, 2 x dual wheel bearing.

Axle Hole diameter: 1 inch

Note: this upgrade kit requires an existing full set of Seamax "Deluxe Launching Wheels" or "Easy Load Launching Wheels".

Extra Bracket Set for Seamax Deluxe Launching Wheels

99.00 USD

2 x Aluminium Bracket

Suitable for Seamax Deluxe Launching Wheels

Installation stainless steel bolts and nuts included

14" Dual Wheel Upgrade Kit for Seamax Deluxe Boat Launching Wheels 2019 Version

99.00 USD

Provide a 4-Wheels system option to "Deluxe Launching Wheels"  (14" Wheel Version * 2019)

Suggested for larger boat with wider transom. Provide better support on soft terrain and sandy beach.

Our new tires are now 14” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.

Package includes: 2 x 14 inches Pneumatic tire, 2 x dual wheel bearing. Marine grade tire and inner tube. overall width of tire 3-3/4 inches

Axle Hole diameter: 1 inch

Note: this upgrade kit requires an existing full set of Seamax Deluxe Launching Wheels with 14 inches Wheels  (Some of photo showing the 12" wheel but we will ship 14" kit)

Extra Bracket Set for Seamax Easy Load Launching Wheels

69.00 USD

2 x Marine Grade Aluminium Bracket

Suitable for Seamax Easy Load Launching Wheels

Installation stainless steel bolt and nuts included

Trailer Dolly for Easy Moving, Max Support 5000 Lbs Weight

79.00 USD

• Tubular steel construction with rust resistant power coat finish
• Large pneumatic tires for easy maneuvering on any surface
• Moves boats, utility and RV trailers easily and safely
• Includes 1-7/8" chrome hitch ball
• Standard with 10" wheels, can upgrade to 12" wheels

Aluminium Portable Boat Carry and Launching Hand Dolly Set

449.00 USD

Features