Electric Air Pump

SUP20D PRO Double Stage 20PSI Electric Air Pump for Inflatable SUP and Boat, Intelligent Firmware with Built-in Temperature Sensor and Timer, Signature Edition

129.95 USD

• Features
• Description
• Specification

• Features

  
  
  
  • Seamax SUP20D PRO Signature Edition air pump is an upgraded version in the SUP20 pumps family. Programmed intelligent proactive digital controller, voltage sensor, temperature sensor, and overheat protection for managed dual stage inflation. Backlit LCD display and audible indicator to provide real-time working status to users. Major parts made of marine grade engineered ABS and Nylon material for durability. Low power consumption, 5-10A (60-120W). Wide range of working temperature and humidity. Regardless daily use during the season or occasionally use in a year, this high quality air pump can always do a good job.
    
    

  • 2019 new Seamax version with firmware and hardware improvement, helps the pump working better in hard condition, such as wide range product support, lower battery voltage or poor 12V socket connection.  This new Seamax version also has built in a smart monitoring feature, when the pump starts to inflate, the computer monitors the real time pressure in every second, based on our Self-Developed smart pump formula, it can find the pump a best timing to switch to 2^nd stage. The computer also monitors the pump internal temperature and continued working time, Auto Stop Protection feature has been built-in.

    
    
  • 1st stage max speed 350L/min; 2nd stage max speed 70L/min, Pressure setting increments 0.5 PSI and support up to 20PSI. Real time pressure monitoring and auto stop once selected pressure reached; High efficient dual air inflators controlled by digital pressure controller module; Supported working range 0.5 - 20 PSI (20 PSI = 1.378 Bar =138 Kilo-Pascal); accurateness 0.01 PSI.
    
    
  • Built-in sand filter for air intake & pump cooling system; Built-in outtake chamber for noise reduce and better efficiency. One-way diaphragm valve to protect the inflator and maximize the speed. Designed for inflatable boat, SUP and paddle board; About 10 minutes to inflate a 12ft SUP or a 9ft inflatable boat (3.5 PSI) with air mat floor (12 PSI) fast and easy.
    
    
  • Super light weight 4Lbs and Dimension only 10”x7”x7” with easy carry handle; Reinforced 3.5ft air hose. Perfect handy size for pumping boats, SUPs and Paddleboards. 360 degree free turning main air hose connector provides flexible pumping positions. Screw-in style adaptors provide perfect air tight.
    
    
  • The pump’s 12V DC connector (Car Cigarette Lighter connector) has a built-in 12A fuse. Cigarette lighter spare fuse is provided with the package. Pump user manual is included in the package and downloadable from our website. 
    
    

• Description

  • Easy to use backlit touch buttons and portable ergonomic handle; Backlit LED screen for pre-set and real-time air pressure display; PSI and Bar dual units display; 9ft Power cord; Reinforced 3.5 FT nylon type air hose suitable for high temperature and high pressure use (Rated at 150°C (302°F) and 30PSI Max); Universal HR air valve adaptor and 3 silicone O-Rings with different thickness can fit all inflatable SUPs. Noise reduction inflators for quiet operation.
    
    
  • This rapid double stage intelligent 12V DC electric pump comes with a digital control and LCD screen to display the set pressure and real-time air pressure. The pump can auto stop at your pre-set air pressure. It can auto stop after max 20 minutes continuously working. So you will never over-inflate the chamber or damage the air pump.
    
    
  • The valve connector with the hose is suitable for inflatable boats and SUPs equipped with HR (Halkey-Roberts), Bravo, Naru or similar type air valves. This kind of air valve has a turning pin or pressing down pin at the middle to control the valve’s Open and Closed position. 3 silicon O-Rings to choose and keep the connection best air tight.
    
    

• Specification

  - Model: Seamax SUP20D

  - Pump Support Rate: 0.5-20 PSI (0.034-1.378 Bar)
  - Digital Sensor Accuracy: 0.01 PSI
  - Controller Method: Pre-programmed digital controller board
  - Max Pumping Speed: 350L/min at 1^st Stage, 70L/min at 2^nd stage
  - Pump Stage 1: Sealed and quiet turbo fan for high volume inflation
  - Pump Stage 2: Engineered cylinder type compressor for high pressure
  - Dual Inflators Switch Point: 0.65 PSI
  - O Ring Thickness: 0.3mm / 0.5mm / 0.6mm
  - Sand Filter: Dual filters for air intake and pump cooling
  - Pump Working Voltage: 11-14V DC 
  - Max Energy Consumption: 10A, 120W (12V) 
  - DC Power Cord Length: 9ft (2.75m) 
  - Air Hose: 3.5ft Length & with HR Valve Adaptors 
  - Product Net Weight: 3.6 Lbs  
  
  

Blue Portable Electric Air Pump 1 - 8.5 PSI for Inflatable Boats and Inflatable Kites (with Built-in 7AH Rechargeable Battery)

215.00 USD

• Specifications
• Features
• Warranty

• Specifications

  Turbo Fan Stage: Max Pump Air 500L per Minute
  Dual Cylinder Stage: Max Working Pressure 60 Kpa (8.5 PSI)
  Digital Air Gauge. Built-in 12V/7AH battery with 110V-240V Smart Charger.
  Air Host Kit.
  Max 45 Minutes Working Time per Battery Charging
  Pressure Setting from 1PSI, Increment per 1 KPA (0.15PSI)
  Multiple Valve Adapters, Digital Control and Real Time Monitoring, Auto Shuts Off when Set Pressure Achieved
  LCD Back Light, Carrying Bag, Support Intake & Outtake (Inflate & Deflate) Dual Actions. 
  
  

  Additional Information

  This pump is suitable for the products that are using the Boston type, HR (Halkey-Roberts), Bravo or similar type air valve, Leafield valve etc. This kind of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. We have the Pump in Kite version, Please know the Kite version pump also good for Inflatable boats and all application same as the regular pump version.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.
  
  Use for Deflation - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.

• Features

  Supported Air Valves - This pump is suitable for the products that are using the HR (Halkey-Roberts), Bravo or similar type air valve. This kind of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. This Pump is the Kite version, Please know the Kite version pump is also good for Inflatable boats and all application same as the regular pump version.
  
  About this pump - Turn on the POWER switch and enter the maximum desired pressure by using the Set Pressure buttons, the set pressure will be shown on the right hand side of LCD screen. (10KPa = 100mbr = 1.45 PSI). Factory default working pressure is set as 25KPa (3.6 PSI).This pressure is suitable for most inflatable boats.
  
  Use as a Deflator - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.
  
  Built-in Battery - 80DB model has a built-in battery and travel charger. The type of this battery is 12V gel battery, lead acid type, battery capacity 7AH to support max 45 minutes working time. The battery will have up to 500 Cycles and 8 years life time if you can follow this maintenance manual. The charger is 110/240V travel type with double charging procedures. When you plug in the charge and connect with the pump, a red light showing on the charger can indicate the battery charging. The max charging current is 1A from the charger.
  
  Using the Pump Min set pressure is 1 PSI (8Kpa), if you only need lower pressure than 1 PSI, you can keep monitoring the screen pressure reading and stop the pump manually. Press the POWER button to start. During inflation, the left hand side of LCD screen should show the pressure that the pump has reached. As soon as the entered pressure has been reached, the inflator turns off automatically. And the inflator can be turned off at any time by pressing the POWER button again. Take off the air hose from the chamber once the pump stops pumping. It is possible to stop the inflator at any time by pressing the (OFF) switch.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.

• Warranty

  For recreational use, the electrical control boards, motor, charger are guaranteed for 2 years. Battery, air hose, valve adapters and carrying bag are guaranteed for 6 months. Warranty for commercial use is limited to six months from purchase date, and 90 days warranty for battery.

Portable Lithium 12V 6AH External Power Supply for SUP Pump Max Output 200W

119.00 USD

• Features
• Specification

• Features

  Special designed to operate with Seamax SUP20D and SUP20S 12V SUP electric air pump.  A full capacity battery level can inflate 2 large inflatable SUPs up to 20PSI, or 4 mid size SUPs up to 16PSI when supporting the SUP20D pump, or fully charge 4 mobile devices, such as iPhone. If it is working with Seamax SUP20D or SUP20S electric air pump, it can support the pump to work for 30-40 minutes.
  
  Promotion - SUP Pump & Lithium Battery Combine Order - Extra 10% Saving Discount Code "web10saving"
  
  With Plug & Play design, power supply will be automatically waked up when electronic device or USB phone cable is connected, and will be automatically put in sleep in 2 minute after all devices are unplugged.  Also great for outdoor use as it is compatible with most portable 12V electronic accessories used in car, such as GPS or tire inflator.
  
  High quality PCB (Power Management Board) unit embedded with this 12V 6AH lithium battery, and built with internal fuse to protect the battery cell from electric circuit shortage. Fully supported to all Seamax SUP electric air pump.  
  
  Backlit LCD display with real-time power meter and port status indicators. Suitable for night time use with 3 x 1W built-in LED flash light with one-button easy operation. Along with anti-slip rubber coating and water resistant DC output socket, this portable power supply is an ideal gear for your outdoor sport activities.
  
  Multiple DC ports with water resistant rubber caps:
  - 1x 5V / 2A USB port for fast charging mobile devices.
  - 1x 5V / 1A USB port for standard charging mobile devices.
  - 1x 12V / 15A cigarette lighter style socket to power Seamax SUP 
  - 1x 12V / 1A charging port
  
  Warranty:  This product is guaranteed for one (1) year from purchase date within USA & Canada. The limited warranty only covers the defective factory parts under normal operating conditions. Seller has the right to refuse the warranty claim if the product shows excessive wear, abuse or misuse. Keep the original sales record and the label on the product for warranty service. Seller pays for two-way shipping fee if a warranty claim is within 60 days from the date of purchase. Buyer pays for one-way shipping fee if the warranty claim is after 60 days and within 180 days from date of purchase. Buyer pays for two-ways shipping fee if the warranty claim is over 180 days from the date of purchase. Please know the shipping cost claim is only available for USA lower 48 states and Canada. Contact the seller to obtain return authorization.
  
  NOTE OF SHIPPING SERVICE, GROUND SHIPPING SERVICE ONLY, NO EXPRESS SERVICE FOR THIS ITEM WHEN CONTAINS LITHIUM ION BATTERY CELL. THANK YOU.
  
  
  
  
  

• Specification

  Battery Capacity:	MSDS certified Lithium Ion 6AH 11.1V
  Total Max Output	200W (12V-180W + 5V-15W + LED 3x 1W)
  Charger Standard	Input 110-240 AC / Output 5V & 12V DC
  Battery Charging Time:	Max 6 hours to fully charged & auto stop
  USB Charging Ports	Compatible with all 5V devices, 1A & 2A
  Cigarette Lighter Output:	12V / Max 15A (Max 180W)
  Product Dimension:	8 x 4.5 x 2 inches (L x W x H)
  Item Net Weight:	1.8 pounds (800g)

Nylon Air Hose Kit for Seamax 20PSI SUP Electric Air Pump - 2 Version

20.00 USD

New or replacement air hose kit for Seamax SUP20S or SUP20D electric air pump

Hose Length: 3.3 Feet (1 Meter) 
Pump connector - Screw in type 100% air tight

Version 1: Same standard as the pump package, Boat and SUP new style Halkey Roberts valve adapter Pre-installed. comes with one 5mm thickness O ring.

Version 2: With exchange-able fitting end for Multiple valve adaptors, As an upgrade kit for your SUP20S or SUP20D for multi--purpose. Traditional type HR adapter comes with 3mm thickness O ring.

Note: Seamax SUP pump comes with 3 different thickness O-rings in the package. 3mm, 5mm and 6mm. All O-rings are compatible with this air hose kit.

 Version 2: Air Hose Kit with Multiple Valve Adapters

Blue Portable Electric Air Pump 1 - 8.5 PSI for Inflatable Boats and Inflatable Kites (without Battery)

Sold Out

• Specifications
• Pump Operation
• Warranty

• Specifications

  Interface: LCD display with back light
  Powertrain: Dual Motors and Double Stages, Electric Control, High Pressure Compressor
  Standard Voltage Input: DC12V / Current: 10A to 40A MAX / Max Power Dissipation: 500W
  Max. Inlet Air: 500L per Min / Max Working Pressure: 60Kpa (8.5 PSI)
  Pressure Increments: Per 1Kpa / 0.15 PSI / Build in Digital Air Gauge
  Maximum Continuous Working Time (Non Stop): 30 Minutes (15 Minutes at 2nd Stages)
  Min. Operation Voltage: DC 11V Max Operation Voltage: DC 14V 
  
  

  Additional Information

  This pump is suitable for the products that are using the Boston type, HR (Halkey-Roberts), Bravo or similar type air valve, Leafield valve etc. This type of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. We have the Pump in Kite version, Please know the Kite version pump also good for Inflatable boats and all application same as the regular pump version.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.
  
  Use for Deflation - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.
  
  

• Pump Operation

  1). Choose the proper fitting for the air valve of your inflatable boat, inflatable kite or paddle board. Put the valve at the inflation position. Attach the correct valve adapter to the inflation hose that comes with your pump. Attach the other end to the pump (smooth round outlet on the pump).
  
  2). Connect the pump’s terminals to the battery paying close attention to the polarity. Make sure the clips are on the same color electrode and properly connected. Otherwise the pump won’t turn on or run properly.
  
  3). Enter the maximum desired pressure by using the set pressure button. The set pressure will be shown on the right hand side of the LCD screen. The pump provides readings in metric (KPa). (Pressure: 10KPa = 100mbr = 1.45 PSI). Factory default working pressure is set at 25KPa (3.6 PSI).This pressure is suitable for most inflatable boats. 45Kpa is 6 PSI to support the inflatable kite.
  
  4). Press the POWER button to start. During inflation, the left hand side of LCD screen should show the pressure that the inflator has reached. As soon as entered set pressure has been reached, the inflator turns off automatically. Take off the air hose from the chamber once the pump stops running. The inflator can be turned off at any time by pressing the POWER button again. It is possible to stop the inflator at any time by pressing this button.
  
  5). The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t be started.

• Warranty

  For recreational use, the electrical control boards, motor, charger are guaranteed for 2 years. Air hose, valve adapters and carrying bag are guaranteed for 6 months. Warranty for commercial use is limited to six months from purchase date.

Smart Charger for Seamax 80DB 12V Electric Air Pump with Built-In Battery

25.00 USD

Smart Charger with Status Light Indicator. Light weight and small travel size.

Input: AC 100-240V 50/60Hz

Output: DC 14.4V 0.8A

Caution: For Indoor Use Only

Nylon Air Hose Kit for Seamax 20PSI SUP Electric Air Pump - Leafield C7 Version

28.00 USD

New air hose kit for Seamax SUP20S or SUP20D electric air pump, Only to fit the inflatable product with leafield C7 air valve.

Seller modified the air hose kit by original leafield valve adaptor. please know other valve adaptors are not included for this modified kit.

Hose Length: 3.3 Feet (1 Meter) 
Pump connector - Screw in type 100% air tight

New Rigid Nylon Air Hose Kit for 80D & 80DB Electric Air Pump - High Temperature & High Pressure Application

28.00 USD

Package

• 5FT reinforced air hose for high pressure inflation
• 2x O-ring with different thickness
• Reinforced hose-to-Pump adapter
• Reinforced Halkey-Roberts valve adapter
• With Leafield C7 compatible valve fitting adapter

Operation Instructions

4) If the hose is damaged due to the hot air near the hose-to-pump connector, cut the damaged portion (approximate 2-inches) and use the new extra hose-to-pump connector.

5) To reinforce the hose after installing the new hose-to-pump adapter, use some electric tape to wrap the air hose for about 2 inches starting from the hose-to-pump connector side.

12V Alligator Clip to Cigarette Lighter Plug Converter for SUP20 Air Pump

15.00 USD

Connect 12V Cigarette Lighter Plug directly to 12V battery terminals

Suitable for Seamax SUP20S & SUP20D 12V electric air pump

Wire length: 16", Gauge for: 15A

Suggested 12V battery capacity: minimum 7AH when using with SUP20 Pump

SUP20S PRO Intelligent 20PSI Electric Air Pump for Inflatable SUP - Signature Edition

99.95 USD

• Features
• Description
• Specification

• Features

  • NEW PRO FEATURES:
    Pump Status Indicator with Display and Warning Beep Sound;
    Voltage Working Range 9V-15V with Built-in Power Protection;
    Built-in Temperature Sensor for Protect Against Overheating;
    
    
  • Engineered in Canada at an affordable price; Major parts made of marine grade engineered ABS and Nylon material more durable. Low power consumption 5 - 10A (60 - 120W). Wide range of working temperature and humidity. Regardless of daily use during the season or occasionally use in a year, this quality pump always does a good job.
    
    
  • This Seamax intelligent SUP20S electric air pump comes with a Digital pressure LCD screen. Designed for inflatable SUP and paddleboard etc. Supported working range 0.5 - 20 PSI (20 PSI = 1.378 Bar =138 Kilo-Pascal); 15 minutes to fully inflate a 12ft SUP to 20 PSI. Max speed:  70L/min; Lightweight 3Lbs; Dimension 9”x5”x5”.
    
    
  • Noise reduction single inflator with high sensitive intelligent pressure controller module, accurateness 0.01 PSI; Pressure setting increments 0.5 PSI; Real-time pressure monitoring, auto-stop once selected pressure reached. Built-in outtake chamber with one-way diaphragm valve for protection and better airtight.
    
    
  • Reinforced 3.5 FT Nylon type air hose suitable for high temperature and high-pressure use (Rated at 150°C (302°F) and 30PSI Max). Perfect handy size for pumping SUPs and Paddleboards. 360 degree free turning main air hose connector provides flexible pumping positions. Screw-in style adapters provide perfect airtight. This design will avoid users’ complaints against poor quality leaky air hose issues and help this pump to last for many years.
    
    
  • The pump’s 12V DC connector (Car Cigarette Lighter connector) has a built-in 12A fuse. Cigarette lighter spare fuse is provided with the package. Pump user manual is included in the package and downloadable from our website.
    
    
    

• Description

  • Easy to use backlit touch buttons and portable ergonomic handle; Backlit LED screen for pre-set and real-time air pressure display; PSI and Bar dual units display; 9 ft Power cord and 3.5 ft nylon air hose, Universal HR air valve adapter and 3 silicone O-Rings with different thickness can fit all inflatable SUPs. Noise reduction inflators for quiet operation.
    
    
  • This intelligent 12V DC electric pump comes with digital control and LCD screen to display the set pressure and real-time air pressure. The pump can auto stop at the pre-set air pressure. It will auto stop after max 20 minutes of continuous working. So you will never over-inflate the chamber or damage the air pump.
    
    
  • The valve connector with the hose is suitable for SUPs equipped with HR (Halkey-Roberts), Bravo, Naru or similar type air valves. This kind of air valve has a turning pin or pressing down the pin in the middle to control the valve’s Open & Closed position. 3 silicon O-Rings to choose and keep the connection best airtight.
    
    

• Specification

  - Model: Seamax SUP20S
  - Pump Support Rate: 0.5 - 20 PSI (0.034 - 1.378 Bar)
  - Digital Sensor Accuracy: 0.01 PSI
  - Controller Method: Pre-programmed digital controller board
  - Max Pumping Speed:  70L/ min
  - Single Stage: Engineered cylinder type compressor for high pressure
  - O Ring Thickness: 0.3 mm/ 0.5 mm/ 0.6 mm
  - Pump Working Voltage: 11-14V DC 
  - Max Energy Consumption: 10A, 120W (12V) 
  - Fuse type: 12A standard, spare fuse included
  - DC Power Cord Length: 9 FT (2.75 m) 
  - Air Hose: 3.5 FT length & with HR Valve Adapters 
  - Pump Net Weight: 2.6 LBS  
  - Pump Dimensions: 9” x 5” x 5”

Seamax Portable Electric Air Pump 1 - 8.5 PSI for Inflatable Boats and Inflatable Kites (without Battery)

128.00 USD

• Specifications
• Pump Operation
• Warranty

• Specifications

  Interface: LCD display with back light
  Powertrain: Dual Motors and Double Stages, Electric Control, High Pressure Compressor
  Standard Voltage Input: DC12V / Current: 10A to 40A MAX / Max Power Dissipation: 500W
  Max. Inlet Air: 500L per Min / Max Working Pressure: 60Kpa (8.5 PSI)
  Pressure Increments: Per 1Kpa / 0.15 PSI / Build in Digital Air Gauge
  Maximum Continuous Working Time (Non Stop): 30 Minutes (15 Minutes at 2nd Stages)
  Min. Operation Voltage: DC 11.0V Max Operation Voltage: DC 14V 
  
  

  Additional Information

  This pump is suitable for the products that are using the Boston type, HR (Halkey-Roberts), Bravo or similar type air valve, Leafield valve etc. This kind of air valve has a turning pin at the middle to control the valve’s Open & Closed position. There are universal valve adapters supplied with the pump to fit it. We have the Pump in Kite version, Please know the Kite version pump also good for Inflatable boats and all application same as the regular pump version.
  
  The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t turn on.
  
  Use for Deflation - You can use it to deflate the same chamber too. Attach the yellow hose onto the deflation side of the inflator (round outlet with notches). Attach the other end to the chamber you wish to deflate.
  
  

• Pump Operation

  1). Choose the proper fitting for the air valve of your inflatable boat, inflatable kite or paddle board. Put the valve at the inflation position. Attach the correct valve adapter to the inflation hose that comes with your pump. Attach the other end to the pump (smooth round outlet on the pump).
  
  2). Connect the pump’s terminals to the battery paying close attention to the polarity. Make sure the clips are on the same color electrode and properly connected. Otherwise the pump won’t turn on or run properly.
  
  3). Enter the maximum desired pressure by using the set pressure button. The set pressure will be shown on the right hand side of the LCD screen. The pump provides readings in metric (KPa). (Pressure: 10KPa = 100mbr = 1.45 PSI). Factory default working pressure is set at 25KPa (3.6 PSI).This pressure is suitable for most inflatable boats. 45Kpa is 6 PSI to support the inflatable kite.
  
  4). Press the POWER button to start. During inflation, the left hand side of LCD screen should show the pressure that the inflator has reached. As soon as entered set pressure has been reached, the inflator turns off automatically. Take off the air hose from the chamber once the pump stops running. The inflator can be turned off at any time by pressing the POWER button again. It is possible to stop the inflator at any time by pressing this button.
  
  5). The inflator operates in two stages which can be identified by the noise of the turbine at the beginning followed by the piston. The inflator switches from turbine to piston automatically. If the chamber pressure is over 7KPa / 1 PSI, the pump will start the 2nd stage only. If the set pressure is lower than the chamber’s pressure, the pump won’t be started.

• Warranty

  For recreational using, the electrical control boards, motor, charger are guaranteed for 2 years. Air hose, valve adapters and carrying bag are guaranteed for 6 months. Warranty for commercial use is limited to six months from purchase date.

Previous Version Soft Air Hose Kit for 80D and 80DB Electric Air Pump

28.00 USD

Package

• 5FT reinforced air hose for high pressure inflation
• 2x O-ring with different thickness
• Reinforced hose-to-Pump adapter
• Reinforced Halkey-Roberts valve adapter

Operation Instructions

4) If the hose is damaged due to the hot air near the hose-to-pump connector, cut the damaged portion (approximate 2-inches) and use the new extra hose-to-pump connector.

5) To reinforce the hose after installing the new hose-to-pump adapter, use some electric tape to wrap the air hose for about 2 inches starting from the hose-to-pump connector side.