139.95 USD
2019 new Seamax version with firmware and hardware improvement, helps the pump working better in hard conditions, such as wide range product support, lower battery voltage or poor 12V socket connection. This new Seamax version also has built-in a smart monitoring feature, when the pump starts to inflate, the computer monitors the real-time pressure in every second, based on our Self-Developed smart pump formula, it can find the pump the best timing to switch to 2nd stage. The computer also monitors the pump internal temperature and continued working time, Auto Stop Protection feature has been built-in.
- Pump Support Rate: 0.5-20 PSI (0.034-1.378 Bar)
- Digital Sensor Accuracy: 0.01 PSI
- Controller Method: Pre-programmed digital controller board
- Max Pumping Speed: 350L/min at 1st Stage, 70L/min at 2nd stage
- Pump Stage 1: Sealed and quiet turbo fan for high volume inflation
- Pump Stage 2: Engineered cylinder type compressor for high pressure
- Dual Inflators Switch Point: 0.65 PSI
- O Ring Thickness: 0.3mm / 0.5mm / 0.6mm
- Sand Filter: Dual filters for air intake and pump cooling
- Pump Working Voltage: 11-14V DC
- Max Energy Consumption: 10A, 120W (12V)
- DC Power Cord Length: 9ft (2.75m)
- Air Hose: 3.5ft Length & with HR Valve Adaptors
- Product Net Weight: 3.6 Lbs
139.00 USD
Battery Capacity: |
MSDS certified Lithium Ion 6AH 11.1V |
Total Max Output |
200W (12V-180W + 5V-15W + LED 3x 1W) |
Charger Standard |
Input 110-240 AC / Output 5V & 12V DC |
Battery Charging Time: |
Max 6 hours to fully charged & auto stop |
USB Charging Ports |
Compatible with all 5V devices, 1A & 2A |
Cigarette Lighter Output: |
12V / Max 15A (Max 180W) |
Product Dimension: |
8 x 4.5 x 2 inches (L x W x H) |
Item Net Weight: |
1.8 pounds (800g) |
215.00 USD
105.00 USD
Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model.
-- ACHILLES
LT2-A265 LT4-B295 LS2-A240 LS4-B270
LEX: LEX77-B255 LEX88-B270 LEX96-B295
LSR: LSR290-B320 LSR310-B350
LSI: LSI230-B255 LSI260-B295 LSI290-B320 LSI310-B350 LSI335-C360 LSI365-C420
SPD: SPD290-B320 SPD310-B350 SPD335-C390 SPD365-C420
RIGID HB-FX: 270FX-B295 300FX-C330
RIGID HB-LX: 240LX-B255 280LX-C300 315LX-C360 350LX-D400
RIGID HB-DX WITH SEAT & CONSOLE: HB280DX-C330 HB315DX-C360 HB350DX-D400
FOLDABLE: SG124-C390 SG140-D430 SG156-D500 SU14-D430 SU16-E500 SU18-E600
*
-- MERCURY
DINGHY: 200-A210 240-A240 270-A265
ROLL UP: 240-B270
SPORT & ADVENTURE SPORT: 240-B270 270-B290 310-B320 340-B350
AIR DECK (PVC/HP): 240-B270 270-B290 310-B320 340-B350
DYNAMIC: RIB260-B295 RIB280-B320 RIB310-B350
SEA RUNNER: 300-C300 350-C360 430-D430
HEAVY DUTY: 380-D430 430-D4500
AMANZI: 350-D430 400-E460
*
-- SEAMAX
AIR: 230-A240 270-B270 320-B320
HD: 330-B350 360-C390 380-C420 430-D470 470-D500
OCEAN: 290-B295 320-B320 380-C390 430-D430
OCEAN-T: 380T-C390 430T-D430 500T-E500
SPORT EMARINE: 240-B240 270-B270 305-B320 365-C360 420-D430
*
-- ZODIAC
PROJET: 350TC4-D400 420TC4-D430
YACHTLINE DELUXE: YL340DL-C390 YL380DL-C420 YL420DL-D500 YL470DL-E550 YL530DL-E600
CADET: RIB220-B255 RIB260-C300 RIB310-C360 RIB340-D400
COMPACT: COMPACT250-C300 COMPACT300-C330
CADET FASTROLLER ACTI-V: FR285-C330 FR325-C360 FR360-C390
CADET ROLL UP: 200-B255 240-V270 260-B295
CADET SOLID: 260S-C300 285S-C330 310S-C360 340S-D400
CADET AIRLITE: 240-B270 260-C300
ZOOM: 230-A265 260AERO-B295 260S-B295 310S-B350 350S-C420
BOMBARD TYPHOON ROLL-UP/AERO: 200-A210 235-A240 265-A265 310-B320 360-c360
136.00 USD
Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model. This model check list is recommended for boat model year 2015 to 2017. Or buyer should refer to the boat cover size chart.
-- ACHILLES
LT2-A265 LT4-B295 LS2-A240 LS4-B270
LEX: LEX77-B255 LEX88-B270 LEX96-B295
LSR: LSR290-B320 LSR310-B350
LSI: LSI230-B255 LSI260-B295 LSI290-B320 LSI310-B350 LSI335-C360 LSI365-C420
SPD: SPD290-B320 SPD310-B350 SPD335-C390 SPD365-C420
RIGID HB-FX: 270FX-B295 300FX-C330
RIGID HB-LX: 240LX-B255 280LX-C300 315LX-C360 350LX-D400
RIGID HB-DX WITH SEAT & CONSOLE: HB280DX-C330 HB315DX-C360 HB350DX-D400
FOLDABLE: SG124-C390 SG140-D430 SG156-D500 SU14-D430 SU16-E500 SU18-E600
*
-- MERCURY
DINGHY: 200-A210 240-A240 270-A265
ROLL UP: 240-B270
SPORT & ADVENTURE SPORT: 240-B270 270-B290 310-B320 340-B350
AIR DECK (PVC/HP): 240-B270 270-B290 310-B320 340-B350
DYNAMIC: RIB260-B295 RIB280-B320 RIB310-B350
SEA RUNNER: 300-C300 350-C360 430-D430
HEAVY DUTY: 380-D430 430-D470
AMANZI: 350-D430 400-E460
*
-- SEAMAX
AIR: 230-A240 270-B270 320-B320
HD: 330-B350 360-C390 380-C420 430-D470 470-D500
OCEAN: 290-B295 320-B320 380-C390 430-D430
OCEAN-T: 380T-C390 430T-D430 500T-E500
SPORT EMARINE: 240-B240 270-B270 305-B320 365-C360 420-D430
*
-- ZODIAC
PROJET: 350TC4-D400 420TC4-D430
YACHTLINE DELUXE: YL340DL-C390 YL380DL-C420 YL420DL-D500 YL470DL-E550 YL530DL-E600
CADET: RIB220-B255 RIB260-C300 RIB310-C360 RIB340-D400
COMPACT: COMPACT250-C300 COMPACT300-C330
CADET FASTROLLER ACTI-V: FR285-C330 FR325-C360 FR360-C390
CADET ROLL UP: 200-B255 240-V270 260-B295
CADET SOLID: 260S-C300 285S-C330 310S-C360 340S-D400
CADET AIRLITE: 240-B270 260-C300
ZOOM: 230-A265 260AERO-B295 260S-B295 310S-B350 350S-C420
BOMBARD TYPHOON ROLL-UP/AERO: 200-A210 235-A240 265-A265 310-B320 360-c360
90.00 USD
Gray color canopy is the standard, Black color canopy is the Sunbrella type stronger and double life time. Options for Bimini: Pontoon Fitting Patch Kit, Nylon Deck Mount Kit, Rear Support Pole. Combo price with those options is available from this listing. Seamax Completed set of Bimini system is suitable for inflatable boat, aluminum boat and fiberglass boat up to 24ft. We can provide one stop Bimini Solution.
Seamax is the inflatable boat builder, so we can have good knowledge to make our Bimini. Now we are the only seller providing professional fitting for inflatable boat. Our solution is the best in the market and offering PVC and Hypalon both. Product is accepted by many end-users and resellers in the market. Our Bimini system can support 30 knots boating speed no problem.
Bimini for Inflatable Boat - Seamax Bimini Pontoon Fitting Kit is special designed for PVC & Hypalon inflatable boats. You may only want one set of it to go with your Bimini, so you can use the Bimini and Oar Lock at the same time. If your inflatable boat is sitting on the boat trailer, so you don't need to deflated the boat when finishing your trip every time. Then you may want a full package including 2 set fitting patch and rear support pole. In this solution, the Bimini can be installed as permanent and work better.
Bimini for fiberglass boat and aluminum boat - Please choose the Bimini with deck mount kit package, so you can have everything you need to install the Bimini on your rigid hull boat and reach the best result.
NOTE: IF PRODUCT IS NOT LIST AVAILABLE FROM OUR WEBSITE, PLEASE FEEL FREE TO CONTACT SELLER TO DIRECT PURCHASE. THANKS!
37.00 USD
New or replacement air hose kit for Seamax SUP20S or SUP20D electric air pump
Hose Length: 3.3 Feet (1 Meter)
Pump connector - Screw in type 100% air tight
Version 1: Same standard as the pump package, Boat and SUP new style Halkey Roberts valve adapter Pre-installed. comes with one 5mm thickness O ring.
Version 2: With exchange-able fitting end for Multiple valve adaptors, As an upgrade kit for your SUP20S or SUP20D for multi--purpose. Traditional type HR adapter comes with 3mm thickness O ring.
Note: Seamax SUP pump comes with 3 different thickness O-rings in the package. 3mm, 5mm and 6mm. All O-rings are compatible with this air hose kit.
Version 2: Air Hose Kit with Multiple Valve Adapters
View full product details80.00 USD
Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model.
-- ACHILLES
LT2 (A265) / LT4 (B295) / LS2 (A240) / LS4 (B270)
LEX: LEX77 (B255) / LEX88 (B270) / LEX96 (B295)
LSR: LSR290 (B320) LSR310 (B350)
LSI: LSI230 (B255) / LSI260 (B295) / LSI290 (B320) / LSI310 (B350) / LSI335 (C360) / LSI365 (C420)
SPD: SPD290 (B320) / SPD310 (B350) / SPD335 (C390) / SPD365 (C420)
RIGID HB-FX: 270FX (B295) / 300FX (C330)
RIGID HB-LX: 240LX (B255) / 280LX (C300) / 315LX (C360) 350LX (D400)
RIGID HB-DX WITH SEAT & CONSOLE: HB280DX (C330) / HB315DX (C360) / HB350DX (D400)
FOLDABLE: SG124 (C390) / SG140 (D430) / SG156 (D500) / SU14 (D430) / SU16 (E500) / SU18 (E600)
*
-- MERCURY
DINGHY: 200 (A210) / 240 (A240) 270 (A265)
ROLL UP: 240 (B270)
SPORT & ADVENTURE SPORT: 240 (B270) / 270 (B290) / 310 (B320) / 340 (B350)
AIR DECK (PVC/HP): 240 (B270) / 270 (B290) / 310 (B320) / 340 (B350)
DYNAMIC: RIB260 (B295) / RIB280 (B320) / RIB310 (B350)
SEA RUNNER: 300-C300 350-C360 430-D430
HEAVY DUTY: 380 (D430) / 430 (D450)
AMANZI: 350 (D430) / 400 (E460)
*
-- SEAMAX
AIR: 230 (A240) / 270 (B270) / 320 (B320)
HD: 330 (B350) / 360 (C390) / 380 (C420) / 430 (D470) / 470 (D500)
OCEAN: 290 (B295) / 320 (B320) / 380 (C390) / 430 (D430)
OCEAN-T: 380T (C390) / 430T (D430) / 500T (E500)
SPORT EMARINE: 240 (B240) / 270 (B270) / 305 (B320) / 365 (C360) / 420 (D430)
*
-- ZODIAC
PROJET: 350TC4 (D400) / 420TC4 (D430)
YACHTLINE DELUXE: YL340DL (C390) / YL380DL (C420) / YL420DL (D500) / YL470DL (E550) / YL530DL (E600)
CADET: RIB220 (B255) / RIB260 (C300) / RIB310 (C360) / RIB340 (D400)
COMPACT: COMPACT250 (C300) / COMPACT300 (C330)
CADET FASTROLLER ACTI-V: FR285 (C330) / FR325 (C360) / FR360 (C390)
CADET ROLL UP: 200 (B255) / 240 (B270) / 260 (B295)
CADET SOLID: 260S (C300) / 285S (C330) / 310S (C360) / 340S (D400)
CADET AIRLITE: 240 (B270) / 260 (C300D
ZOOM: 230 (A265) / 260AERO (B295) / 260S (B295) / 310S (B350) 350S (C420)
BOMBARD TYPHOON ROLL-UP/AERO: 200 (A210) / 235 (A240) / 265 (A265) / 310 (B320) / 360 (C360)
168.00 USD
68.00 USD
Product Content Polyurethane. M.E.K. Harmful if inhaled; eye irritations. May cause sensitization if inhaled. Repeated exposure may cause skin dryness and cracking; Keep away from sources of ignition-No smoking; Don’t breathe vapor / spray. In case of contact with eyes, rinse immediately with plenty of fresh water & seek medical attention. Use Only in well-ventilated areas. Don’t smoke or work near open flames, sparks or other heat sources.
Glue and all chemical materials are dangerous goods. Keep out of Reach of Children. Store in a cool and safe spot and keep the product quality for up to 5 years.
View full product details
239.00 USD
Originally designed with 3D-work by Seamax Marine back in 2011, Now it is the 2nd edition released in 2019. Seamax Deluxe Boat Launching Wheels system is made by the marine grade T6 aluminum alloy with CNC processing and shiny looking anodized coating against the corrosion. Thus the product is good for saltwater use. Small parts are all made by solid stainless steel and reinforced Nylon. The air-filled tire is lab-tested (1000 LBS), and is great to support a MAX loading of 600 LBS in all condition. A great add-on for inflatable, aluminum, and fiberglass boats.
BENEFIT of its new design - With the 4 stages of length and 4 wheel arm position, the dolly can be adjusted while afloat in the boat, leaving or coming into the dock. The dolly system can also bring different performance positions for boat launching. The wheel arm length increment is 2.5” per stage. Plus the wheel’s diameter, the range of length is 23 - 30 inches.
The wheel arm has a 60° and 90° locking position to move up and down. The upper-60° position can free up more space on the top and side of the transom. The lower 60° position lets the wheels run at the same level as the prop, and thus turns the wheels as a prop guard when boat launching.
The transom bracket installation area is about 8 x 3 inches. Shorter transom bracket design brings more possible installation for all types of boats with different transom. The brackets can be installed at the waterline top position, so to avoid the water comes into the screw holes. We had developed a profile for the transom bracket in 2019. Now the bracket only requires 2 bolts to install. Easier to put it on your boat with the same loading capacity.
TRIPLE heavy-duty, TRIPLE quality! Product is made by Seamax Canada with 2 years limited warranty and 100% Customer Satisfaction guaranteed! The Quick Operation Features of the Deluxe Boat Dolly include - spring load locking pin for wheel arm position adjustment; solid spring load buttons for wheel arm length adjustment; and quick released lock pin for wheel arm and wheel bearing.
Our new tires are now 14” in diameter and about 4” wide. They are made of 4 plies reinforced vehicle grade natural rubber which holds up well against UV rays, heat and saltwater for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high-quality marine-grade tires and rims will last you for many years of trouble-free use。
Word Wide Buyer
Australia and New Zealand - visit www.amazon.com.au
UK and other Europe Countries - visit www.amazon.co.uk
MAX LOAD: This dolly set is designed for boats with solid outboard transom. For easier moving, total weight should not exceed 600 Lbs including boat, outboard, and all gears.
INSTALLATION: This dolly set should only be installed by an adult with some experience in working with tools. To install the wheelset properly, you will need to drill 5/16” holes in the plywood transom for the mounting brackets. It is very important to locate the position of the holes correctly. Please check carefully including checking the wheel arm position before starting to drill any holes.
MAINTENANCE: Wash it after using it from saltwater or sandy beach. Check tire pressure before every use. Don’t store the wheels under the sun or beside the heat to maximize its lifetime. Take the wheel arm off from the transom bracket when storing your boat. Lube the spring load dolly system if needed. Always keep the lock pin on the dolly bracket.
TIRE INFLATION: Dolly tires may not be fully inflated when shipping; please only give 15-20 PSI pressure at room temperature before using. Best to use a car tire digital air pump to prevent tire over-inflation. Tire over-inflated will cause damage and the warranty is not covered.
14" Dual wheel upgrade kit is available for this Deluxe boat launching wheelset for heavy loading application or sandy beach use. We suggest the boat 14ft and up to use this upgrade kit, then you can have a wide enough transom to support 4 wheels operation.
WARRANTY: Manufacturer 2 years Parts Limited Warranty within USA & Canada. 60 days of free replacement on any defective components. Please take photos or return the product or parts to the retailer you purchased them from if there is a warranty issue. You can also contact Seamax for technical support.
38.00 USD
New air hose kit for Seamax SUP20S or SUP20D electric air pump, Only to fit the inflatable product with Leafield C7 & D7 air valve.
Seller modified the air hose kit by the original Leafield valve adaptor. please know other valve adaptors are not included for this modified kit.
Hose Length: 3.3 Feet (1 Meter)
Pump connector - Screw-in type 100% airtight
View full product details
59.00 USD
Suitable for 12" Wheel Version Seamax Boat Launching Wheels Set (All models with 1" diameter axle)
Wheel Model: 4.10/3.50-6
Max Tire Diameter: 12 inches
Wheel Axle Diameter: 1 inch
Suggested Air Pressure: 12 to 15 PSI (Max 30PSI)
Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.
Note: Not intended for highway use. Rinse the product with fresh water after use in salt water. Cover from sun light when no in use and maximize the life time.
View full product details
25.00 USD
Smart Charger with Status Light Indicator. Light weight and small travel size.
Input: AC 100-240V 50/60Hz
Output: DC 14.4V 0.8A
Caution: For Indoor Use Only
View full product details
166.00 USD
Note: The model check list is a general guideline. It is recommended to confirm the actual dimensions of your boat before selecting a boat cover model.
-- ACHILLES
LT2-A265 LT4-B295 LS2-A240 LS4-B270
LEX: LEX77-B255 LEX88-B270 LEX96-B295
LSR: LSR290-B320 LSR310-B350
LSI: LSI230-B255 LSI260-B295 LSI290-B320 LSI310-B350 LSI335-C360 LSI365-C420
SPD: SPD290-B320 SPD310-B350 SPD335-C390 SPD365-C420
RIGID HB-FX: 270FX-B295 300FX-C330
RIGID HB-LX: 240LX-B255 280LX-C300 315LX-C360 350LX-D400
RIGID HB-DX WITH SEAT & CONSOLE: HB280DX-C330 HB315DX-C360 HB350DX-D400
FOLDABLE: SG124-C390 SG140-D430 SG156-D500 SU14-D430 SU16-E500 SU18-E600
*
-- MERCURY
DINGHY: 200-A210 240-A240 270-A265
ROLL UP: 240-B270
SPORT & ADVENTURE SPORT: 240-B270 270-B290 310-B320 340-B350
AIR DECK (PVC/HP): 240-B270 270-B290 310-B320 340-B350
DYNAMIC: RIB260-B295 RIB280-B320 RIB310-B350
SEA RUNNER: 300-C300 350-C360 430-D430
HEAVY DUTY: 380-D430 430-D4500
AMANZI: 350-D430 400-E460
*
-- SEAMAX
AIR: 230-A240 270-B270 320-B320
HD: 330-B350 360-C390 380-C420 430-D470 470-D500
OCEAN: 290-B295 320-B320 380-C390 430-D430
OCEAN-T: 380T-C390 430T-D430 500T-E500
SPORT EMARINE: 240-B240 270-B270 305-B320 365-C360 420-D430
*
-- ZODIAC
PROJET: 350TC4-D400 420TC4-D430
YACHTLINE DELUXE: YL340DL-C390 YL380DL-C420 YL420DL-D500 YL470DL-E550 YL530DL-E600
CADET: RIB220-B255 RIB260-C300 RIB310-C360 RIB340-D400
COMPACT: COMPACT250-C300 COMPACT300-C330
CADET FASTROLLER ACTI-V: FR285-C330 FR325-C360 FR360-C390
CADET ROLL UP: 200-B255 240-V270 260-B295
CADET SOLID: 260S-C300 285S-C330 310S-C360 340S-D400
CADET AIRLITE: 240-B270 260-C300
ZOOM: 230-A265 260AERO-B295 260S-B295 310S-B350 350S-C420
BOMBARD TYPHOON ROLL-UP/AERO: 200-A210 235-A240 265-A265 310-B320 360-c360
Sold Out
Seat Cushion Size | Under-Seat Bag Size | Suitable for Boat Size |
L 33" x W 8" x H 1" | L 26" x W 8" x H 13" | 8-11 FT Inflatable Boat |
L 37" x W 8" x H 1" | L 28" x W 8" x H 13" | 10-12 FT Inflatable Boat |
L 39" x W 8" x H 1" | L 29" x W 8" x H 13" | 12-13 FT Inflatable Boat |
L 42" x W 8" x H 1" | L 31" x W 8" x H 13" | 14-16 FT Inflatable Boat |
L 45" x W 8" x H 1" | L 35" x W 8" x H 13" | 15-18 FT Inflatable Boat |
Choosing a Right Size
Seamax seat cushions are suitable for most standard plywood or aluminum bench seat. The seat cushion covers the max 9-inches width bench seat, and the standard is 8 inches width. The seat cushion length could be up to 2-inches shorter than the bench seat for best result, which gives approximate 1-inch gap on each side of the seat.
View full product details
118.00 USD
65.00 USD
Features:
Size Check List:
Marine Grade Sunlitec Fabric (MGSF)
We want to introduce our newly developed thermal welded 3 layers Sunlitec fabric. The outer layer of Sunlitec is the special high-performance synthetic fabric similar to Acrylic fabric. It is resistant to sunlight UV and many harsh chemicals including salt water. The mid-layer is the water resident micro-poly fabric foam. It is resistant to temperatures from outside and inside as well as impeding the water from going through and providing breathable performance. The inner layer is the marine grade polyester 300D for protecting the tear and wear from inside and as back support. After the Sunlitec manufacturing process, all three layers stay together as one fabric. It has a solid structure, better performance, looks great, and is lightweight. We are the only company to produce these boating accessories with Marine Grade Sunlitec Fabric (MGSF). We hope you will enjoy these high quality and affordable accessories.
Our Warranty - Fabric structure is covered by a 2-years limited warranty on all items using the Seamax Sunlitec material, and a 1-year limited warranty on sewing lines, tie-down strings, zipper line, and plastic parts. Physical damage or lack of maintenance damage is not covered under this warranty. Normal wear and tear are not covered under this warranty
55.00 USD
2 x Aluminum Oars with Quick Lock Pin
Available assembled lengths: 5.3, 5.7, 6 Feet
Black or Grey color to choose from
Suitable Oar Length:
5.3 FT oars for up to 10.5 FT boats
5.7 FT oars for 12.5 FT to 15.5 FT boats
6 FT oars for 16.5 FT to 20 FT boats
View full product details
Sold Out
View full product details
119.95 USD
- Model: Seamax SUP20S
- Pump Support Rate: 0.5 - 20 PSI (0.034 - 1.378 Bar)
- Digital Sensor Accuracy: 0.01 PSI
- Controller Method: Pre-programmed digital controller board
- Max Pumping Speed: 70L/ min
- Single Stage: Engineered cylinder type compressor for high pressure
- O Ring Thickness: 0.3 mm/ 0.5 mm/ 0.6 mm
- Pump Working Voltage: 11-14V DC
- Max Energy Consumption: 10A, 120W (12V)
- Fuse type: 12A standard, spare fuse included
- DC Power Cord Length: 9 FT (2.75 m)
- Air Hose: 3.5 FT length & with HR Valve Adapters
- Pump Net Weight: 2.6 LBS
- Pump Dimensions: 9” x 5” x 5”
158.00 USD
55.00 USD
Additional Information (Standard 2012)
Seamax AIR270, AIR320, Ocean320, HD330 - Size A 34"
Seamax Ocean380, Sport 360, HD360, HD380, Ocean380T (Ver. 2012) - Size B 37"
Seamax Ocean430, Sport430, HD430, HD470, Ocean430T (Ver. 2012) - Size C 42"
Seamax Ocean 500T (2012 Version or Earlier) - Size D 49"
NEW Ocean T Series since 2014 Version ( PVC or Hypalon)
Ocean380T (2018) - Length 40"
Ocean430T - 470T (2018) - Length 45"
Ocean500T - 600T (2018) - Length 52"
35.00 USD
Newly re-designed Black fiberglass reinforced composite material propeller, updated pitch, camber and thickness for high thrust application. Better performance with new propeller and minimizes efficiency lost through cavitation.
Suitable for Seamax 2019 PowerMax edition trolling motor. Fiberglass Reinforced Black Nylon 3 Blade Propeller. Package included: Stainless steel washer, screw cap, and lock pin; (British system & metric system tighten hardware are both included)
Replacing the Propeller (Refer to User Manual, Page 8).
To replace the propeller, hold the blade and loosen the nut using the propeller wrench (Fig. D). Remove the nut and propeller. If propeller is stuck, hold one blade by hand and tap on the back side of the other blade with a hard blunt object. If necessary, repeat the procedure for the other blade until the propeller comes off. If propeller pin is bent, replace it. Align pin (Fig. E) when refitting propeller and tighten nut securely.
View full product details55.00 USD
View full product details
79.00 USD
Provide a 4-Wheels system option to "Deluxe Launching Wheels 2017 or Earlier Model" and "Easy Load Launching Wheels". (12" Wheel Version)
Suggested for larger boat with wider transom. Provide better support on soft terrain and sandy beach.
Our new tires are now 12” in diameter and about 4” wide. They are made of 4 ply reinforced vehicle grade natural rubber which holds up well against UV rays, heat and salt water for up to ten years. To prevent air loss, we use an advanced butyl inner tube for our wheels with an “L” style cooper air valve. The rim is made of reinforced nylon with a 1” diameter hole for the axle with NO bearing as this product is made for marine use. These high quality marine grade tires and rims will last you for many years of trouble free use.
Package includes: 2 x 12 inches Pneumatic tire, 2 x dual wheel bearing.
Axle Hole diameter: 1 inch
Note: this upgrade kit requires an existing full set of Seamax "Deluxe Launching Wheels" or "Easy Load Launching Wheels".
45.00 USD
Pull-Up for Transom with thickness of 1" or 1-1/2"
The order set includes: 1x Drain Valve. 1x Sikaflex 291i marine sealant, 3.5oz tube.
General Instruction of Drain Valve Replacement
1) First remove the old drain valve and check the drain valve hole on the transom to make sure the new drain valve matches the hole dimensions. Then clean up all the dirt from the hole. If there is water in the drain hole, wash it again and leave it dry in the air. Make sure all the condition are good before starting to install the new drain valve.
2) Put the Sikaflex 291i on the drain hole surface about 1mm thickness (5-15g). Wear a glove and use a finger to push the sealant fully coated at the drain hole. Wait 30-60 minutes to let the new sealant coating stay well before putting the new drain valve in.
3) Apply about 5 g of the Sikaflex 291i on the valve and transom contact surface before installation. It helps the valve to get perfect water tight result.
4) Many inflatable boats come with plywood transom with wrong sealant used in the factory. The waterproof coating need to be refinished. Boat's old drain valve may have already caused some water leaking and damage to the transom. This Sikaflex sealant perfectly helps to finish the replacement.
General Instruction of Sikaflex 291i (100g pack):
Professional grade marine adhesive/ sealant used by boat builders and yards to bond and bed boat components structurally. Fast strength build-up overnight. Use above and below the waterline. Comes with nozzle. All purpose adhesive sealant, bond to hull and structural members. Bedding compound, light bonding, fast-cure polyurethane sealant.
If a partial pack remains, you can simply squeeze the air out of the tube using the included tool, thereby extending the shelf life of opened product. Includes application nozzle and dispensing/ storage tool.
View full product details28.00 USD
4) If the hose is damaged due to the hot air near the hose-to-pump connector, cut the damaged portion (approximate 2-inches) and use the new extra hose-to-pump connector.
5) To reinforce the hose after installing the new hose-to-pump adapter, use some electric tape to wrap the air hose for about 2 inches starting from the hose-to-pump connector side.
Sold Out
2 x Aluminium Bracket
Suitable for Seamax Deluxe Launching Wheels
Installation stainless steel bolts and nuts included
View full product details
69.00 USD